Mitel Sx-2000 Integrated Communications System Control Sheet Manual

SX-2000@ INTEGRATED 
COMMUNICATIONS SYSTEM 
Safety 
Instructions 
I”, @ -1rademarlc ol MM Corpomtlon. 
0 copyrlgm 1992. Mltel colporauon. 
All rights reserved. 
Printed In Canada 
0 
MlTEL@  

Safety Instructions 
NOTICE 
The information contained in this document is believed to be accurate in all re- 
spects but is not warranted by Mite1 Corporation (MITEL@). The information is 
subject to change without notice and should not be construed in any way as a 
commitment by MITEL or any of its affiliates or subsidiaries. MITEL and its affili- 
ates and subsidiaries assume no responsibility for any errors or omissions in this 
document. Revisions of this document or new editions of it may be issued...

Table of Contents 
1. IMPORTANT SAFETY INSTRUCTIONS 
General 
................................................................... 203 l-l 
Useof Notices ............................................................. 
203 l-2 
UseofSymbols ............................................................ 203 l-2 
General Installation Summary 
................................................. 203 l-3 
Fuse and Component Replacement 
............................................. 203 l-3 
Identification and...

Safety Instructions 
Table l-4 DC System Grounding Cables (External) ............................. 
203 l-l 8 
Table l-5 SX-2000 VS System Cabinet Grounding Cables (External) .............. ,203 l-23 
Table l-6 SX-2000 FD System Peripheral Cabinet Grounding Cables (External) ....... 203 l-26 
Table l-7 SX-2000 SG System Sub-assemblies .............................. 
,203 l-26 
Table l-8 SX-2000 S System Sub-assemblies ................................. 203 l-29 
Table l-9 SX-2OOOVS System Sub-assemblies...

IMPORTANT SAFETY 
INSTRUCTIONS 
These instructions are intended as a general guide to provide basic installation 
information which is necessary for the proper and safe functioning of this equipment. 
1 WARNING ) Failure to follow all instructions may result in improper equipment operation 
and/or risk of electrical shock. 
General 
l Read and understand all instructions, Keep these instructions with the equipment. 
l Do not attempt to install or service this equipment unless you are skilled in the...

Safety Instructions 
Use of Notices 
1.1 The following information provides an explanation of the notices which appear on the 
product and in the practices for this product: 
DANGER 
WARNING 
CAUTION Danger indicates an imminently hazardous situation which, if not 
avoided will result in death or serious injury. 
Warning indicates a potentially hazardous situation which, if not 
avoided, could result in death or serious injury. 
Caution indicates a potentially hazardous situation which, if not 
avoided,...

Important Safety Instructions 
General Installation Summary 
Power Source This product is intended to operate from an electrical source rated as 
indicated below. Each cabinet shall be powered from a separate 
branch circuit wired in accordance with the National Electrical Code or 
the Canadian Electrical Code, as applicable. 
SX-2000 SG -48 Vdc 6OA 
sx-2000 s -48 Vdc 25A 
120 Vat 15A 
60 Hz 
SX-2000 VS -48 Vdc 15A 
120 Vat 15A 
60 Hz 
SX-2000 FD 120 Vat 15A 60 Hz 
Equipment Location This product shall...

Safety Instructions 
Identification and location of Circuit Cards for Installation 
1.4 The mechanical design consists of a metal enclosure, a card cage, and an 
interconnecting backplane which define the arrangement and position ofcircuit card 
assemblies. Installation of a circuit card assembly is performed by sliding it along the 
card cage guides in the appropriate slot until the card is firmly seated into the mating 
connector on the backplane. Refer to Figure 1-I through Figure 1-5 for the specific...

Important Safety Instructions 
(A)UPPERSHELF-SHELF2 
1 2 3 4 5 6 7 6 9 10 11 12 13 14 15 16 17 16 19 20 
(B)LOMRSHELF-SHELF1 
1 2 3 4 5 6 7 6 9 10 11 
12 13 14 15 16 
17 16 19 20 
* * * * * * 
NOES: 1. The minbnum system musthavethe cardsindicated by* 
installed In slots as shown. 
2. 
3. RefertoTsble l-11, DSUs andTable 1-12, Pit&for lists of approved cards. 
Ocmtd Fl4M II cad not required with Main Cotifflec II card. 
Figure l-2 SX-2000 S System Circuit Card Locations 
9125-060-203-NA Issue 1 
Revision...

Safety Instructions 
(A) PERIPHERALSHELF 
123456 7 6 9 10 11 12 13 14 15 16 17 16 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 
*** * 
I 
PERIPHERALINTERFACE CARDS I I I 
I 
PERIPHEIWL 
SWKCH 
(B) COFrmOLSHELF 
1 2 3 4 5 6 7 6 9 10 11 12 13 14 15 16 17 16 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 
I 
MAIN CONTROLCOMPLE% 
I I I 
MESSAGE SWilCH CIRCUIT SWITCH DIGITALSERWCE UNrCS 
NOTE: RefettoTablel-11, DSUsandTable l-12, PlCqfaklsof approved cards 
203 l-6 
Figure l-3 SX-2000 SG System Circuit Card...