Home
>
Mitel
>
Communications System
>
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Have a look at the manual Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Modem interconnect Panel CONTENTSPAGE 1. INTRODUCTION General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Reason for Issue . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . . . . . . 1 2. MODEM INTERCONNECT PANEL General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LIST OF TABLES 2-lModem Interconnect Panel Connections . . . . . . . . . . . . 3 LIST OF CHARTS CHART Tl.TLE 2-linstall a Modem Interconnect Panel into a Datacabinet 9000 . . . . . . . . , . . . . . . , . . . . . . . . . . . . 5 FIGURETITLEPAGE 2-1Modem interconnect Panel Connectors.............4 2-2Installation of Cardfile Rail.......................6 PAGELIST OF ILLUSTRATIONS . . .III
Modem Interconnect Panel 1. INTRODUCTIONGeneral 1 .OlThis Section describes the MITEL Modem Interconnect Panel, part number 9141-940-100-NA. THE MITEL Modem Interconnect Panel is designed and approved only for installation in the Mite1DATACABINET 9000. Reason for Issue 1.02This Section is issued to describe the Modem Interconnect Panel. Page 1
Modem Interconnect Panel 2. MODEM INTERCONNECT PANEL General2.01The Modem Interconnect Panel provides a method to connect a voice tip-ring pair from the PABX to a modem, and to connect the MI/MIC leads from the data set to the modem. Sixteen circuits are provided; each is the same, except for the tip-ring connection to the 25-pair cable. Figure 2-1 shows the connections to a Modem Inter- connect Panel. Connections 2.02The Teledapt jacks (FROM MODEM and TO DATASET) are con- nected together in pairs (pin 2 to pin 2 and pin 5 to pin 5). The FROM MODEM Teledapt connector voice tip (pin 3) and voice ring (pin 4) are connected to the 25-pair cable connector pins as listed in Table 2-1. These cable pairs are then connected to ONS ports on the PABX. TABLE2-1 MODEM INTERCONNECT PANEL CONNECTIONS DATASET Jack/25-pairConnector Modem Jack pairtipring 161641 151540 141439 131338 12.I237 111136 10IO35 9934 8833 7732 6631 5530 4 429 3328 2227 1126 Page 3
SECTION MITL9141-753-528-NA 3C KA0346ElROFigure 2-l Modem Interconnect Panel Connectors Page 4
Modem Interconnect Panel CHART 2-l INSTALL A MODEM INTERCONNECT PANEL INTO A DATACABINET 9000 CAUTION: Only MITEL designed and approved equipment may installed within a DATACABINET 9000. StepAction 1.Unpack and inspect the Modem Interconnect Panel for damage or missing items. 2.Turn off the power switch and remove the line cord from its outlet. Open the doors of the cabinet. 3. 4. 5.install the cardfile rails for the Modem Interconnect Panel immediately above an existing DATASHELF 9100 or Modem Interconnect Panel. Refer to Figure 2-2. The Modem Interconnect Panel(s) must always be installed immediately above the DATASHELF 9100 to maintain correct cooling air flow. Place the Modem Interconnect Panel onto the cardfile rails and fasten to the front cabinet side rails with the screws provided. Run the cable groups through the cable entry slots. Form each cable bundle neatly up the right side rail, and attach securely to the brackets on the side rails; also attach to the strain reliefs at the back of the Modem Interconnect Panel. 6.Install 25-pair cables in through one of the cable entry slots on the rear PDU panel and route up the left side of the cabinet and attach to side rail brackets separately from ac cords. 7. 8. 9. 10.Close up the covers of the cable access slots. Connect the 25-pair cables to their associated MDF, and cross-connect the MDF blocks as required. Attach one end of a 4-wire line cord to the jack usually labeled “TELCO” on the rear of the modem. Attach the other end of the line cord to the Teledapt jack labeled “FROM MODEM” on the Modem Interconnect Panel. Attach one end of a 4-wire line cord to the “PHONE” jack of the Rack Mounted DATASET. Attach the other end of the line cord to the Teledapt jack labeled “TO DATASET” on the Modem Interconnect Panel. 11.Complete the PABX Customer Data Entry for the Modem Interconnect Panel. 12.Close and lock Cabinet doors. 13.Connect the power cord from the DATACABINET 9000 to its ac outlet. bePage 5
CABINET ---e---vSIDE RAIL CARDFILE RAILIFAN UNIT SECTION MITL9141-753-528-NA KAO601 EOR0Figure 2-2 Installation of Cardfile Rail Page 6