Mitel SX-200 DIGITAL Pabx Information Manual

MITEL STANDARD PRACTICE SECTION MITLSI 98-093-320~NA 
Issue 2, September 1986 
SX-200” DIGITAL 
PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX) 
SYSTEM TEST PROCEDURES 
Copyright of MITEL Corporation 1986 
TM - Trademark of MITEL Corporation 
@Registered Trademark of MITEL Corporation  

System Test Procedures 
CONTENTS 
PAGE 
I. INTRODUCTION 
................................... l-l 
General .......................................... 
l-l 
Reason for Reissue ............................... 
l-l 
SUPERSET 3TM and SUPERSET qTM Sets 
................. l-l 
Section Overview 
................................. l-l 
Test Equipment .................................. 
1-2 
Associated Sections 
............................... l-2 
initial System State 
............................... l-2 
2....

System Test Procedures 
TABLE TITLE 
PAGE 
2-l System Access .............................. 2-l 
LIST OF CHARTS 
CHART TITLE 
PAGE 
2-l 
2-2 
2-2 
2-4 
2-5 
2-6 
2-7 
2-8 
2-9 
2-10 
2-l 1 
2-12 
2-l 3 
2-14 
2-15 
2-16 
2-l 7 
2-18 
2-19 
3-l 
3-2 
4-l 
4-2 
4-3 
4-4 
4-5 
4-6 
4-7 
4-8 
4-9 
4-l 0 
4-l 1 
4-12 
4-13 
4-14 
4-l 5 
4-l 6 
4-17 
4-18 
4-19 Logging In and Out of the System .............. 2-2 
Setting System Date ......................... 2-4 
Setting System Time ............................

System Test Procedures 
CHART TITLE PAGE 
5-l 
5-2 
5-3 
5-4 
5-5 
5-6 
5-7 
5-8 
5-9 
5-10 
5-l 1 
5-12 
5-13 
5-14 
5-l 5 
5-16 
5-17 
5-18 
5-19 
5-20 
5-21 Answering Calls ............................. 5-2 
Originating Calls ............................. 5-3 
Call Hold And Retrieve ........................ 5-4 
Recall ..................................... 6-5 
Serial Call .................................. 5-6 
Attendant-Controlled Conference ............... 5-6 
Abbreviated Dial...

System Test Procedures 
1. INTRODUCTION 
General 
1.01 
This Section details the system tests to be performed after the 
system installation (refer to Section MITL9108-093-200-NA, In- 
stallation) and programming (refer to Section MITL9108-093-210-NA, 
Customer Data Entry) have been completed. Upon completion of the 
tests detailed in this Section, all programming system options and 
features will have been verified. 
Reason for Reissue 
1.02 
This Section has been reissued to provide procedures for sys-...

System Test Procedures 
Test Equipment 
1.05 System tests are designed to be carried out without specialized 
test equipment. 
Associated Sections 
1.06 The following Sections are also associated with system tests: 
a MITL9108-093-200-NA, Shipping, Receiving, and Installation 
0 
MITL9108-093-206-NA, Installation Forms 
0 
MITL9108-093-315-NA, Attendant Console Description 
0 
MITL9108-093-350-NA, Troubleshooting 
0 
MITL9108-093-35l-NA, RS-232 Maintenance Terminal. 
Initial System State 
1.07 
Before...

System Test Procedures 
2. MAINTENANCE TERMINAL COMMAND VERIFICATION 
General 
2.01 Successful completion of the following tests will confirm that 
the Maintenance Terminal has been correctly installed and can 
access the SX-200@ DIGITAL PABX to perform directed diagnostic and 
maintenance commands satisfactorily for each of the different levels 
of entry. Section MITLSI 08-093-351 -NA, RS-232 Maintenance Termi- 
nal, is required for reference during these tests. 
Note: In verifying the functions...

System Test Procedures 
CHART 2-1 
LOGGING IN AND OUT OF THE SYSTEM 
Step Action Verify 
1 
Ensure the terminal is Screen displays a flashing cursor. 
connected and turned on. 
2 Press RETURN twice. Screen displays: 
1 - VT-100 
2 - TTY TYPE 
SELECT A TERMINAL TYPE: 
3 Press 1, and RETURN Screen displays: 
1 - MAINTENANCE 
2 - CDE 
6 - QUIT 
SELECT AN APPLICATION (OR QUIT TO START OVER): 
4 Press 1, and RETURN System responds with: 
ENTER USERNAME: 
5 Enter INSTALLER, and System responds with: 
press...

System Test Procedures 
CHART 2-l (CONT’D) 
LOGGING IN AND OUT OF THE SYSTEM 
Step Action Verify 
8 Press 2, and RETURN. System responds with prompt for username. 
9 Enter INSTALLER, and System responds with prompt for password. 
press RETURN. 
10 Enter 1000, and press 
RETURN. System responds as in Step 6. If Authorization Failure 
appears, return to Step 1. Repeat Steps 1 to 3, then Steps 
8 and 9. 
System clears screen, then draws the Customer Data 
Entry menu (FORMS). 
11 Press 6 System responds with...

System Test Procedures 
Setting System Date 
2.04 System date may be set from the Maintenance Terminal. The 
new date will be reflected on the Maintenance Terminal display, 
the Attendant Console LCD display, and SUPERSET qTM set LCD dis- 
plays. Chart 2-2 shows the steps for testing setting of the system 
date. 
CHART 2-2 
SETTING SYSTEM DATE 
Step I Action Verify 
4 
Press 1 (DATE softkey). 
5 
6 
Access MAINTENANCE 
application. 
Press 1 
(SYSTEM softkey). 
Press 1 (SET softkey). 
Enter date according...