Mitel SX-200 DIGITAL Pabx Information Manual

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message 
Access Code XXXXX conflicts with 
SUPERSET line number 
Meaning 
The code entered has already been defined as a 
SUPERSET@ line extension number in Form 09, 
SUPERSET@ Set Lines. Select a new code or change 
the SUPERSET@ line extension number. 
Access Code XXXXX conflicts with the The code entered has already been defined as a Hun 
Access Code for HUNT GROUP NUM XX Group Access Code in Form 17, Hunt Groups. Select...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
Attempting to enter invalid access code A blank access code is not allowed. 
Attempting update/delete of a device that The selected device is being used; modify this device 
is currently in use at a later time. 
Bay/Slot/Circuit XX/XX/XX is already The specified bay/slot/circuit is assigned elsewhere. 
assigned Select a new bay/slot/circuit number or change the 
assignment of that bay/slot/circuit number....

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message 
Iisk is write-protected - data was not 
Nritten to disk 
Meaning 
Remove the write-protect tag from the disk. 
Re-insert the disk in the disk drive and activate the 
write process again. 
Iisk is not ready - data was not written The disk was not ready. initiate the write process at 
:o disk a later time. 
Iisk I/O failure - database may be Due to the disk I/O failure, the database may be 
zorrupted corrupted. Exit...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message 
Iorm number XX cannot be accessed 
Meaning 
The selected form number is reserved for future use 
or the selected form number has restricted user 
access. Refer to Form 27, Form Access Restriction 
for the level of access for each form. 
‘arm number out of range! The selected Form number is invalid. The range is 1 
to 32 with the exception of Forms 11, 12 and 28. 
Refer to Table 4-2, Available Forms. 
iigh power...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
Must delete the appearances of XXXXX All appearances of the station number (or Prime Line 
on all sets before deleting set number) must be deleted before that set can be 
removed from the system. 
Must enter first choice for route list to be In Form 24, ARS: Route Lists, the FIRST field must be 
defined (leave no gaps) specified with a valid Route List number before the 
SECOND field is specified. 
Neither...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
ROUTE LIST out of range. Valid range is The selected Route List number is invalid. The range 
(1 - 100) is 1 to 100. Refer to Form 24, ARS: Route Lists. 
ROUTE out of range. Valid range is (1 - The selected Route number is invalid. The range is 1 
200) to 200. Refer to Form 23, ARS: Route Definition. 
ROUTE PLAN out of range. Valid range is The selected Route Plan number is invalid. The range 
(1 - 50) is 1...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message 
Meaning 
The Bay/Slot/Circuit - XX/XX/XX cannot Devices are assigned to the selected bay/slot/circuit. 
be programmed Before a new card type can be programmed for the 
bay/slot/circuit, these devices must be removed frorr 
the system’s database. 
The Bay/Slot/Circuit - XX/XX/XX is not The specified circuit number is not applicable for 
present these bay and slot numbers. Re-enter the bay and 
slot numbers without...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
The power rating of the UNIVERSAL CARD The power rating of the Universal Card is IO. 
s exceeded. Therefore, the number of modules that can be 
installed on the Universal Card depends on the 
individual power rating of the modules. The Console 
Module has a power rating of 5, the Receiver/Relay 
Module has a power rating of 2, the Music on 
Hold/Pager Module has a power rating of 1 and the 
E&M Trunk Module...

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
-he value X is outside valid range for The selected Hunt Group number is invalid. The 
iUNT GROUP (1 - 50) range is 1 to 50. 
-he value XX is outside valid range for In Form 29, Device Interconnection Table, there are 
NTERCONNECT NUMBER (1 - XX) only 25 Interconnect Numbers. 
-he value XX is outside valid range for The selected Pickup Group number is invalid; the 
‘ICKUP GROUP (1 - 50) range is 1 to 50....

Customer Data Entry (CDE) 
TABLE 4-45 (CONT’D) 
PROGRAMMING ERROR MESSAGES 
Error Message Meaning 
Total string is too long. Limit is 26 digits The total number of digits in the DIGITS TO BE 
ANALYZED field plus the digits in the LEADING 
DIGITS field cannot exceed 26. Refer to Form 26, 
Digit Strings. 
TRUNK GROUP must be entered for a 
route to be defined To complete the Route definition, the Trunk Group 
number must be specified. Refer to Form 23, ARS: 
Route Definition. 
TRUNK NUMBER XX does not...