Mitel SMART L CALL CONTROLLER Hardware Installation Manual

SECTION MITL8350-047-102-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 46  

SECTION MITL8350-047-102-NA 
8. TECHNICAL CIRCUIT DESCRIPTION 
INTRODUCTION 
8.01 
This part will be added at a later date. For the present, refer to 
Appendix C, Figures C-l and C-Z of the General Information 
Manual for an overall block diagram, and a simplified electrical diagram 
of the Controller, respectively. 
Page 47  

SECTION MITL8350-047-102-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 48  

SECTION MITL8350-047-1 OZ-NA 
9. PHYSICAL MAINTENANCE AND TROUBLESHOOTING 
PHYSICAL MAINTENANCE 
9.01 The SMarT-1’” PAV, as is evident, is a fully self-contained unit. 
As such, it has no user repairable parts. If the warranty seal 
over the unit fasteners is broken, the warranty is void. In case of 
failure, replace the Controller as follows: 
I) Power down the unit. This will cut-through the subscriber side 
to the CO side. 
2) Remove the RJ31KA31 plug from the Telco supplied socket. 
The shorting bars...

SECTION MITL8350-047-102-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 50  

SECTION MITL8350-047-102-NA 
APPENDlX A 
FCC INTERCONNECTION REQUIREMENTS 
Al.01 This equipment has been approved by the Federal Communica- 
tions Commission (FCC) as not being harmful to the telephone 
network when connected directly to the telephone lines through the 
standard connection cabling provided with the unit. This section is 
applicable to telephone interconnection in the United States. 
Al.02 Prior to the interconnection of this equipment, the local tele- 
phone company is to be notified;...

SECTION MITL8350-047-102-NA 
Al.06 There are no user repairable parts within the unit. It is sealed 
against user maintenance. If opened, all warranties are voided. 
Al.07 No cabling or wiring changes within the unit are permitted by 
the user. Plug-ended cables, as detailed in this document, are 
to be used for all external connections between the unit and the 
telephone company interface jack. 
Al.08 Power supply components and cabling is only to be changed or 
maintained by MITEL DATACOM INC. or by an...

SECTION MITL8350-047-102-NA 
APPENDIX B 
OVERALL TOPICAL INDEX 
CONTENTS PAGE 
ACCOUNT CODE CONFIRMATION/REROUTE TONES 
SEE ROUTE RELATED PARAMETERS 38 
SEETABLE 6-4 ._ _..... __. __ _........_ .__ ._ 35 
SEE TABLE 6-5 36 
ACCOUNT CODE TVPE 
SEE ROUTE RELATED PARAMETERS 37 
SEETABLE 6-4 .._......... _........._...... 34 
SEE TABLE 6-5 35 
ACCOUNT CODE VERIFICATION 
SEE OPERATING DESCRIPTION 19 
ACCOUNT CODE WARNING TONES 
SEE DIALER DESCRIPTION 4 
SEE ROUTE RELATED PARAMETERS 37 
SEE TABLE 6-4 35 
SEE...

SECTION MITL8350-047-102-NA 
ENTERING SPEED CALLS CONTENTS PAGE 
SEE DETAILED PROGRAMMING 41 
SEE OPERATING DESCRIFTION 20 
SPEED CALL FORMAT 20 
EXIT DATA CONFIRMATION 
SEE SPECIAL FUNCTIONS 29 
SEE TABLE 6-l 27 
EXIT PROGRAM MODE 
SEE SPECIAL FUNCTIONS 28 
SEE TABLE 6-l 27 
EXIT PROGRAMMING SEE USER OPERATION 24 
MEMORY SPACE ESTIMATING METHOD 
CONTROLLER MEMORY CAPACITY 45 
MODE OF OPERATION 
SEE TABLE 5-2 22 SEE RS-232 PORT SPECIFICATIONS 7 
EXITING PROGRAM MODE MOUNTING 
SEE SPEED CALL ENTRY 21 SEE...

SECTION MlTL8350-047-102-NA 
CONTENTS PAGE 
SEE UNPACKING, INSTALLATION AND ORDERING INFORMATION. 12 
PROGRAMMABLE PROGRESS TONES 
SEE DIALER DESCRlmlON 4 
SEE OPERATING DESCRIPTION 19 
PROGRAMMING ACCESS CODE 
SEE DIALER DESCRlmlON 4 
PROGRAMMING EXAMPLES 
SEE DETAILED PROGRAMMING 40 
PROGRAMMING EXAMPLES (PAW 
SEE TABLE 6-6 40 
PROGRESS TONES 
SEE DIALER DESCRIPTION 4 
R51T 
SEE ROUTE RELATED PARAMETERS 36 
SEE TABLE 6-4 34 
R64T 
SEE ROUTE RELATED PARAMETERS 37 
SEE TABLE 6-4 34 
R59T 
SEE ROUTE...