Home > Mitel > Communications System > Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Here you can view all the pages of manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 251

SECTION MITL8350-047-102-NA 
Dialer. This mode causes the Dialer to become an interface between a 
centralized terminal and the telephone line (i.e., the Dialer becomes a 
Tone-to-ASCII converter to allow the display of received tones to the 
screen, and an ASCII-to-Tone converter to allow the remote program- 
ming of another Dialer (or any other device that can be programmed 
by the use of DTMF (Tone)). 
SYSTEM WIDE PARAMETERS 
6.14 Table 6-2 below lists the System Wide Parameters that are 
programmable...

Page 252

SECTION MITL8350-047-102-NA 
where the brackets 
[ 1 enclose the parameter digits to be entered on 
the terminal keyboard by the user. The brackets will not be displayed 
on the screen. 
6.17 OOOt - This parameter tells the Dialer the number of entries to 
be entered in the Speed Call tables (7nnn). Any number of 
speed calls up to the maximum selected number may be entered after 
programming this parameter. For the method of programming Speed 
Calls, refer to paragraph 6.43 of this part. The only...

Page 253

, 
SECTION MITL8350-047-102-NA 
Table 6-3 (Cont’d), Trunk Related Parameters 
ENTER DEFAULT DESCRIPTION 
NOTE: If ‘x19t’ Off-Hook Progress Tone is set to a ‘1’ or 
enabled, the progress tone will not occur until 
‘x08t’ timer has expired or reached 700ms. The 
Off-Hook Progress Tone is 200ms in duration. 
x19t 
x22t 1 Off-Hook Progress Tone, where ‘t’ equals: 
0 = Off-Hook Progress Tone Disabled 
1 = Off-Hook Progress Tone Enabled 
Reserved (See 01 It) 
NOTE: Whether System Option ‘xl It’ (PAV...

Page 254

SECTION MITL8350-047-10%NA 
on the programming terminal, or when programming with a DTMF 
telephone, simply dial the ‘5085’ as follows: 
1 DIAL 1 HEAR 1 DIAL 1 HEAR 1 
where p indicates a single progress tone and hb indicates a 
progress tone (two beeps) as heard in the telephone receiver. 
6.23 x19t - This command programs the Controller to use double 
or not 
use Off-Hook Progress tone when the user lifts the receiver. 
The default for the command is disable Off-Hook Progress tone. For 
example, if it...

Page 255

SECTION MITL8350-047-102-NA 
Table 6-4, Primary Route Related Parameters 
ENTER DEFAULT DESCRIPTION 
r51t 0 
Route Progress Tones (beeps - p), where ‘t’ equals: 
0 = None 
3 = b&P 
I=) 6 = kbbkP& 
4 = Mb& 
2 = Pb 5 = PPbaP 7 = PbMbPP 
8 = &k&h&&b 
NOTE: These Route Progress Tones are 100ms in duration 
with IOOms of silence between them. Route Pro- 
gress tones will be given to the user before the 
Dialer cuts the Central Office audio through. 
r54t 1 Account Code Type where ‘t’ in System option ‘Ollt’...

Page 256

SECTION MITL8350-047-102-NA 
Table 6-4 (Cont’d), Primary Route Related Parameters 
ENTER DEFAULT DESCRIPTION 
r59t 0 
Account Code Warning Tones (beeps - b) where ‘t’ equals: 
0 = None 
3 = bJJd 6 = bbdP)t) 
l=b 
4 = 8b6U 7 = P&#UPPd 
2 = 6/, 
5 = bBPbb 
6 = bb#Ub/ld#h 
NOTE: Warning tones are 400ms ON and 400ms OFF. The 
warning tones start after expiration of r53t Timer. 
If the user fails to enter a digit before the speci- 
fied number of tones expires, the user is returned 
a re-order tone of 200ms...

Page 257

SECTION MITL8350-047-102-NA 
Table 6-5 (Cont’d), Alternate Route Related Parameters 
ENTER DEFAULT DESCRIPTION 
Initial Acct. Code 
New Acct. Code 
4 = 
Same as ‘2’ plus 10 
* = Same as ‘8’ plus 10 
more digits. more digits. 
5 = Same as ‘3’ plus 10 # = Same as ‘9’ plus 10 
more digits. more digits. 
PAV Code Type, where ‘t’ in System option ‘01 It’ 
(PAV) is set to a 
‘1’ or enabled, and where ‘t’ equals: 
Use Initial Account Code 
I= No Account Code. 
2= Fixed length of one to nine digits. Send all...

Page 258

, 
SECTION MITL8350-047-102-NA 
between tones. The tones will be present in the telephone receiver 
before the Dialer cuts the Central Office audio through. The default 
selection for ail eight routes is ‘0’ or no progress tones. A maximum of 
eight tones can be selected by entering a number from 1 to 8 for ‘t’. ‘r’ 
is a number from 1 to 4 to select the route for the tones. For example, 
if it is desired to program Route 2 for four progress tones by use of a 
terminal, the command would be entered as:...

Page 259

SECTION MITL8350-047-102-NA 
been received, or the user is returned a re-order tone. Warning tones 
are 400 ms ON and 400 ms OFF. The re-order tone is 200 ms ON and 
200 ms OFF. The default selection for this parameter is ‘0’ or no tones. 
6.30 For a programming example, if it was desired to program Al- 
ternate Route 3 for eight warning tones, the command during a 
terminal programming period would be displayed as: 
> [47981 
> 
Or if a DTMF telephone were used to program the same example, 
simply dial...

Page 260

SECTION MITL8350-047-102-NA 
SEARCH TABLE ZERO CHANGES 
Default Addition 
6.36 
An additional default entry has been added to Search Table 
Zero to allow the use of a PAV List Maintenance Code. This 
code is dialed by the user when maintaining the Positive Account Code 
list. It is only valid when PAV is enabled by selection of parameter 01 It 
where ‘t’ equals ‘1’. 
Table Template Action Description 
803 
#OH WX 
DTMF ‘#K+’ is the PAV List Maintenance Code 
Action Digit Addition 
6.37 
One action digit...
Start reading Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Related Manuals for Mitel SMART L CALL CONTROLLER Hardware Installation Manual

All Mitel manuals