Mitel SMART L CALL CONTROLLER Hardware Installation Manual

SECTION MITL8350-047-102-NA 
Table 3-l (Cont’d), SMarT-1 tm Hardware Specifications 
SPECIFICATION 
DIAL TONE 
CO 
SIDE FEED: Gain 300 Hz 
INTERNAL FEED: 350 Hz 
DTMF RECEIVER 
LEVEL 
LEVEL DIFFERENCE 
FREQ: To receive 
To not receive 
DURATION 
TIME BETWEEN TONES 
ROTARY RECEIVER 
MAKE IMPEDANCE 
MAKE DURATION 
BREAK IMPEDANCE 
BREAK DURATION 
RATE 
DTMF SENDER 
LEVEL 
FREQUENCY 
DURATION (Programmable) 
ROTARY SENDER 
TIMING (Programmable) 
TIMING (At 60/40): Make 
Break 
RATE (At 60/40) 
INTERDIGIT...

SECTION MITL8350-047-102-NA 
PARAMETER 
BAUD RATE: 
PARITY: 
BITS PER CHARACTER: 
BIT EIGHT SENSE: 
MODE: 
OPERATION: RS-232 PORT 
3.02 
Table 3-2 below contains the specifications for the SMarT-I’” 
Dialer RS-232 Auxiliary Port. This port may be used for 
pro- 
gramming or for SMDR Output. 
Table 3-2, RS-232 Port Specifications 
SPECIFICATION 
110 to 9600 Baud programmable; default 
= 1200 Baud 
None 
Eight bits per character with one stop 
bit. 
Space 
On line. 
Full duplex mode. 
ELECTRICAL/MECHANICAL...

SECTION MITL8350-047-102-NA 
3.05 
The specifications in the Tables above are subject to change 
without notice. The inclusion of ‘n/a’ for a specific parameter 
means that the specification is not available at the time of this pub- 
lication. It will be added at a later date. 
Page 8  

SECTION MITL8350-047-102-NA 
4. UNPACKING, INSTALLATION AND ORDERING INFORMATION 
SHIPPING AND RECEIVING 
4.01 The SMarT-I’” Dialer with PAV is shipped in a single carton that 
contains the Dialer, the Power Supply, a Wall Mounting Bracket, 
four RJ31X Cables and appropriate documentation. All of these items 
are protected within the carton by Styrofoam inserts. 
Note: Some production units do not require the wall mounting 
brackets since these units are mounted to a wall by use of 
keyslots included on...

SECTION MITL8350-047-102-NA 
RJ31WCA31A 
CABLES 
DOCUMENTATIOI 
DIALER 
CARDBOARD 
FLAP DETAIL 
Figure 4-1, Equipment Unpacking and Repacking 
Page 10  

SECTION MlTL8350-047-102-NA 
SINGLE UNIT 
CARTON 
 
 /-- 
/-- 
 /-- 
 _-- 
‘Y--- /-- 
 
 /.-- 
 
I-  
MULTI-UNIT 
CARTON 
Figure 4-2, Multi-Unit Packing and Repacking 
Page 11  

SECTION MITL8350-047-102-NA 
O-85% humidity range. 
POWER REQUIREMENTS 
The customer must provide a single phase power receptacle 
with the following recommendations: 
115V, 60Hz fused and capable of delivering 350mA per unit 
installed. 
The power receptacle should be wired and fused independently 
from all other receptacles that are not controller related. 
A warning tag should be attached to circuit breaker type fuses 
to prevent unauthorized manual operation. 
The power receptacle should not be...

SECTION MITL8350-047-102-NA 
TRUNK 
CONNECTIONS 
[Cl / 
COMPUTER 
PORT (RS-232) 
[Dl 
Figure 4-3, Controller I/O Connections 
110 
VAC 
cl 0 
0 
SMART-1 
CONTROLLER 
POWER 
SUPPLY 
RJ3lX 
CA31A 
’ 1 L__-_______I 
‘L______--____-___I I 
L-,-,___,,__,__,,,,_,,I 
=n 
Figure 4-4, Typical Controller Installation Configuration 
Page 13  

, 
SECTION MlTL8350-047-102-NA 
CENTRAL 
OFFICE 
LINES MDF DF 
CENTRAL OFFICE ‘SPLIT’ TYPE 
DEMARC 
STATION BLOCK 
i T_ 
a-_ T 
_-_ 
ST 
--- -- _ 
- -- 
SR 
- -- 
- -- - 
- -- _ EQUIPMENT 
- -- - 
- -- _ 
- -- - 
‘66 BLOCK BRIDGE BRIDGE 
OR RJZlX CLIPS CLIPS 1 1 
RJBlX I I 
MDF OR CAPlA 
(T) TIP 
(R) RING 
L--l-aI-,ld----J 
I I I 
Figure 4-5, Typical Connection Configuration 
14 20 
25 
yrJ SIGNAL 
1 
FRAME GND 
2 
RxD 
(Signal in) 
3 
TxD (Signal Out) 
4,5 
TIED TOGETHER 
6,8,20 TIED TOGETHER 
7 GND 
c...

SECTION MITL8350-047-102-NA 
1 
I 
!- 
Figure 4-7, USOC RJ3lX Jack and Cable ASSY. 
Page 15