Home > Mitel > Communications System > Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Here you can view all the pages of manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 191

SECTION MITL835t.b047-l OO-NA 
TABLE 17 CON’T: TROUBLESHOOTING CHART 
PROBLEM 
Alternate search tables not being ac- 
cessed. PROBABLE CAUSE 
Unit has been defaulted with a 903 com- 
mand. 
Alternate search tables not selected in 
parameter x22. 
Improper programming of alternate 
search tables (821 through 835). 
Alternate access, authorization, area 
code, etc., not programmed. 
Correctly programmed OCC number is 
going out over DDD. May be normal if NON detection is en- 
abled (see 6R5); the...

Page 192

SECTION MITL8350-047-l OO-NA 
APPENDIX A 
GLOSSARY OF TERMS 
Al.01 The following pages include a Glossary of Common Terminol- 
ogy that might be encountered in this manual. It is presented in 
the tabular format of ‘term’ followed by definition. It does not include 
all possible terms that may be encountered, but tries to include those 
that may not be common knowledge to the reader. 
GLOSSARY OF TERMS 
TERM 
ACCESS NUMBER DEFINITION 
The telephone number used to access the Other Common 
Carrier (OCC)....

Page 193

SECTlON MITL8350-047-l OO-NA 
TERM 
CENTRAL OFFICE 
(CO) 
DEFINITION 
A telephone switching system used to interconnect sub- 
scribers together. It is usually located at a point that is cen- 
tral to the subscribers. 
CENTRAL PROCESSING 
UNIT The circuitry in a computer that controls the computer’s op- 
eration by interpreting and manipulating the information 
stored in the computer’s memory (RAM or ROM). 
CENTREX Service providing direct inward and outward dialing for PABX 
extensions. The PABX is...

Page 194

SECTION MITL8350-047-l QO-NA 
TERM 
FOREIGN EXCHANGE 
(FW 
DEFINITION 
A classification of subscriber service that indicates service 
from any other central office other than the central office 
that would normally serve a subscriber. For example, a tele- 
phone in N.Y. has a Washington number assigned to it. 
GROUND START A method of signaling to the Central Office. This signaling 
requires that a ground be applied to the RING side of the 
Line to indicate an Off-hook condition. 
HERTZ (Hz)...

Page 195

SECTION MITL8350-047-l OO-NA 
TERM 
OFFICE CODE 
NW 
OTHER COMMON 
CARRIER (OCC) 
PRIVATE 
AUTOMATIC 
BRANCH EXCHANGE 
(PABX) 
PRIVATE BRANCH 
EXCHANGE (PBX) 
ROM DEFINITION 
Any of the 792 codes that can be used as an address for a 
10,000 line unit of Central Office. 
A telephone system that provides long distance calls via 
other than normal carrier facilities, usually at a lower rate. 
A telephone system located on the customer’s premises 
(Private Exchange), that allows calling between extensions...

Page 196

SECTION MITL8350-047-l OO-NA 
TERM 
SPEED DIALING DEFINITION 
The automatic dialing of a stored number by a microproces- 
sor or similar unit. The process presupposes that the user 
will dial a single digit to cause the unit to dial many digits 
automatically, saving time and effort. 
STATIC Interference caused by electrical disturbances in the atmo- 
sphere, or any man-made electromagnetic device. 
SWITCHING SYSTEM A device that interconnects two or more subscriber circuits. 
TANDEM MODE When used with...

Page 197

SECTION MITL8350-047-l OO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
; . . 
d 
Page A-6  

Page 198

SECTION MITL8350-047-l OO-NA 
APPENDIX B 
FCC INTERCONNECTION REQUIREMENTS 
General 
81.01 
This equipment has been approved by the Federal Communica- 
tions Commission (FCC) as not being harmful to the telephone 
network when connected directly to the telephone lines through the 
standard connection cabling provided with the unit. This section is 
applicable to telephone interconnection in the United States. 
81.02 Prior to the interconnection of this equipment, the local tele- 
phone company is to be...

Page 199

SECTION MITL8350-047-l OO-NA 
B1.06 
There are no user repairable parts within the unit. It is sealed 
against user maintenance. If opened, all warranties are voided. 
81.07 No cabling or wiring changes within the unit are permitted by 
the user. Plug-ended cables, as detailed in this document, are 
to be used for all external connections between the unit and the 
telephone company interface jack. 
B1.08 Power supply components and cabling is only to be changed or 
maintained by MITEL DATACOM INC. or by...

Page 200

SECTION MITL8350-047-1 OO-NA 
APPENDIX C 
DIAGRAMS AND ASCII TABLE 
Cl.01 
Figures Cl and C2 on the following pages are a block diagram 
and a simplified electrical diagram for the SMarT-lTM Dialer. 
Table Cl is a listing of the standard 7-bit ASCII codes followed by the 
code equivalents. Table C2 contains Legal Dialer Programming Input 
Characters. 
Page C-l  
Start reading Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Related Manuals for Mitel SMART L CALL CONTROLLER Hardware Installation Manual

All Mitel manuals