Home > Mitel > Communications System > Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Here you can view all the pages of manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 171

SECTION MITL8350-047-l OO-NA 
TABLE 11 CON’T: SEARCH TABLE ENTRIES 
FIRST DIGIT = 8 SEARCH TABLES 
DIAL DEFINITIONS/DESCRIPTIONS 
#6 This is the last digit of the phone number; any other 
dialed digits are the account code unless 154t = 1. A 
route must have been chosen prior to encountering 
a search table with #6 as an action. 
#7 Do nothing (wait for more digits). 
#8 Prefer default route (see x24t). 
#9 When entered as an action, that template entry is 
removed from the search table (i.e.,...

Page 172

SECTION MITL8350-047-l OO-NA 
5.33 The following paragraphs list the default settings and their 
descriptions that are included in the search tables when default 
data is first loaded. 
SEARCH TABLE 801 AND 821 
DEFAULT: 111#71 
If the first digit is a 1, do nothing. 
DEFAULT: 1 x I#71 
If the first digit is a x-, do nothing. 
DEFAULT: I#9 1 0 1 
If the first digit is not a 1 or a SC, force the call onto Route #O. 
SEARCH TABLE 803 AND 823 
DEFAULT: )g)/ 
Stop searching after the receipt of 911. 801...

Page 173

SECTION MITL8350-047-l OO-NA 
SEARCH TABLE 807 AND 827 
DEFAULT: 1 #4 #I #9 5 5 5 0 
Place l+N(O or 1)X-555-xXxX calls on Route #O. 
DEFAULT: #4 #4 #9 #9 #9 #9 #9 #6 
T- 
Stop searching after receipt of NNX-XXXX (local call). 
SEARCH TABLE 808 AND 828 
DEFAULT: #1 #4 #4 #9 #9 #9 #9 #9 #6 
Y 
Stop searching after receipt of l+NNX-XXXX (long distance call 
within the same area code). 
SEARCH TABLE 810 AND 830 
DEFAULT: #4 #I #9 #9 #9 #9 #9 #9 #9 #9 #6 
Stop searching after receipt of N(0 or 1)X-XXX-XxXx...

Page 174

SECTION MlTL8350-047-I OO-NA 
TABLE 12: SPECIAL FUNCTIONS 
FIRST DIGIT = 9 
DIAL DEFINITION/DESCRIPTION 
902 
903 
904 
906 
907 
908 
980mmddhhmm 
999 (or go on-hook) Data confirmation mode: After each three digit prefix de- 
scribed above, the Dialer will display the data if program- 
ming method 1 is employed, or if using methods 2 or 3, the 
Dialer will wait for 0.5 seconds, then send the data out in 
DTMF format. 
Load default data - delete all non-default data. 
Clear all searches (including...

Page 175

SECTION MITL8350-047-l OO-NA 
Note: In the event of an illegal entry, the Dialer will send four long, 
slow beeps to indicate that the entry has been ignored. Wait 
for the tones to stop and then try again. 
METHOD 3 
Tandem Mode 
5.39 Remote programming may be accomplished using a PC or 
dumb terminal in conjunction with a Dialer. The local Dialer will 
perform as an ASCII to DTMF convertor in this mode and also has the 
advantage of visual feedback while programming a remote Dialer. This 
mode is also...

Page 176

SECTION MITL8350-047-IOO-NA 
METHOD 4 
Cloning 
5.46 “Cloning” is a programming method whereby several Dialers 
can be programmed to operate identically once one Dialer has 
been set to the desired functions by another programming method. 
The Dialer that has the pr8-programmed instructions 
and is used to 
‘clone’ another is called the ‘Master’. The unit to b8 programmed by 
this method is called the ‘Slave’. 
5.47 This method must be accomplished by meeting the following 
conditions: 
1. The Master...

Page 177

SECTION MITL8350-047-l OO-NA 
Procedure 
5.49 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
IO. 
11. 
12. 
5.50 The following steps are the procedure to be accomplished to 
clone a Dialer: 
Ensure that the Dialers have been x initialized (see Page IO, 
para. 3.05). 
Power up the Master unit. 
Verify that the desired programming is already resident in the 
Master unit. 
Power up the Slave unit. 
Match the Master and Slave Baud rates. 
Connect the Master and Slave RS-232 port connectors together 
with the Cloning...

Page 178

SECTION MlTL8350-047-IOO-NA 
Do not allow the Master to time out of the program mode 
or otherwise exit the program mode while the units are 
connected via the RS-232 Cloning Cable. The resulting 
SMDR output could cause data corruption of both units. 
The user may wish to turn the Master SMDR off (009 = 0) 
during the cloning and later restore it to its original set- 
ting if needed to minimize this error. A good rule to 
follow is to only have the Cloning Cable connected while 
actually cloning the...

Page 179

SECTION MITL8350-047-IOO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 62  

Page 180

SECTION MITb6%60-Q47-l OO-NA 
6. SPECIFICATIONS 
HARDWARE 
6.01 Table 13 lists all of the hardware specifications for the SMarT- 
lTM Common Carrier Access Dialer and Call Controller. These 
specifications also apply to the SMarT-lATM unit unless otherwise 
noted. 
TABLE 13: SMarT-lTM HARDWARE SPECIFICATIONS 
SPECIFICATION MIN. TYP. MAX. UNITS 
FCC RINGER EQUIVALENCE 0.78 
IDLE LINE, LOOP START 
RINGER IMPEDANCE: 15-60 Hz, 70-IIOV 10 20 K& 
20-3500 Hz, 1OV 1 Mfi 
RINGING SENSITIVITY: 15-60 Hz 40 Volts...
Start reading Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Related Manuals for Mitel SMART L CALL CONTROLLER Hardware Installation Manual

All Mitel manuals