Mitel SMART L CALL CONTROLLER Hardware Installation Manual

SECTION MITL6360-047-l OO-NA 
TABLE 13 CON’T: SMarT-lTM HARDWARE SPECIFICATIONS 
SPECIFICATION MIN. 
TYP. MAX. UNITS 
DIAL TONE 
CO SIDE FEED: 
INTERNAL FEED: 
DTMF RECEIVER 
LEVEL 
LEVEL DIFFERENCE 
FREQ: 
DURATION 
TIME BETWEEN TONES 
ROTARY RECEIVER 
MAKE IMPEDANCE 
MAKE DURATION 
BREAK IMPEDANCE 
BREAK DURATION 
RATE 
DTMF SENDER 
LEVEL 
FREQUENCY 
DURATION (Programmable) 
ROTARY SENDER 
TIMING (Programmable) 
TIMING (At 60/40): 
RATE (At 60/40) Gain 300 Hz 
350 Hz 
To receive 
To not receive 
Make...

SECTION MITL8350-047-l OO-NA 
RS-232 PORT 
6.02 Table 14 below contains the specifications for the SMarT-lTM 
Common Carrier Access Dialer and Call Controller RS-232 Aux- 
iliary Port., This port may be used for programming or for SMDR 
output. 
TABLE 14: RS-232 PORT SPECIFICATIONS 
PARAMETER 
BAUD RATE: 
PARITY: 
BITS PER CHARACTER: 
BIT EIGHT SENSE: 
MODE: 
OPERATION: 
SPECIFICATION 
300 to 19200 Baud programmable; de- 
fault = 1200 Baud 
None 
Eight bits per character with one stop 
bit. 
Space 
On...

SECTION MITL8350-047-l OO-NA 
6.05 The specifications in the Tables above are subject to change 
without notice. The inclusion of ‘n/a’ for a specific parameter 
means that the specification is not available at the time of this pub- 
lication. It will be added at a later date. 
.I 
Page 66  

SECTION MITL8350-047-l OO-NA 
7. MAINTENANCE 
GENERAL 
7.01 
The Dialer, as is evident, is a fully self-contained unit. As such, 
it has no user repairable parts. If the warranty seal over the unit 
fasteners is broken, the warranty is void. In case of failure, replace the 
Dialer as follows: 
1) Power down the unit. This will cut-through the subscriber side 
to the CO side. 
2) Remove the RJ31 plug from the Telco supplied socket. The 
shorting bars in the RJ31X will cut-through to the line. Then, 
3)...

SECTION MITL8350-047-l OO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
3 
. 
Page 58  

SECTION MITL8350-047-l OO-NA 
8. ORDERING INFORMATION 
GENERAL 
PART NO. 
8350-00 1 8.01 Table 16 below lists the part numbers and descriptions of items 
that can be ordered from MITEL DATACOM INC. 
TABLE 16: SMarT-lTM ORDERING INFORMATION 
DESCRIPTION 
SMarT-1: 4 Line Common Carrier Access Dialer and Call Controller. 
Includes Power Pack, RJ31 Cables, and Wall Mount 
Bracket. 
8350-002 SMarT-1A: 2 Line Common Carrier Access Dialer and Call Controller. 
Includes Power Pack, RJ31 Cables, and Wall Mount...

SECTION MITL8350-047-IOO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 70  

SECTION MlTL8850-047-l OO-NA 
9. TROUBLESHOOTING 
GENERAL 
9.01 
The following pages are a troubleshooting chart to assist the 
technician in locating problems on installation. It is presented in 
the form of trouble followed by a description of a probable cause. 
Figures Cl and C2 on pages C2, C3, along with Section 3 and Figures 2 
and 3 will aid in locating the problem. 
TABLE 17: TROUBLESHOOTING CHART 
PROBLEM 
Cannot be programmed from remote lo- 
cation. 
Cannot program a remote unit. 
No Ground...

SECTION MITL8350-047-l OO-NA 
TABLE 17 CON’T: TROUBLESHOOTING CHART 
PROBLEM 
No Dial out. Progress tones are okay, but 
are followed by dialtone. PROBABLE CAUSE 
Unit has been programmed to output 
DTMF while CO is Rotary type. 
Programmed for Loop Start while CO is 
Ground Start. 
No Dial out after programming. Improper programming. 
Dialer in Cut Through mode (x23 = 9). 
If remotely programmed, programmer 
may have neglected to exit program 
mode upon completion. Dialer will time 
out of program mode...

SECTION MITL8350-047-IOO-NA 
TABLE 17 CON’T: TROUBLESHOOTING CHART 
PROBLEM 
Call waiting signal or flash-hook for hold 
.drops call. 
PROBABLE CAUSE 
On-hook timing too short (x03). 
Flash allowed timing too short (x04). 
Flash allowed timing set for a longer pe- 
riod that on-hook timing. 
Failure to acquire dialtone on redial 
functions. 
Dialer re-order tone during slow dialing. 
No Centrex operation. x05 time between release and reseize is 
too short for the particular CO. 
xl 1 inter-digit timeout...