Mitel SMART L CALL CONTROLLER Hardware Installation Manual

SECTION MITL8350-048-l OO-Nk 
/ COMPUTER 
PORT (RS-232) 
[Dl 
Figure 4-3, Controller I/O Connections 
SMART-l 
CONTROLLER 
POWER 
SUPPLY 
RJ2lX 
CA3lA 
Figure 4-4, Typical Controller Installation Configuration 
Page 17  

SECTION WTL8350-048-100-NA 
CENTRAL 
OFFICE 
LINES MDF DF 
CENTRAL OFFICE “SPLIT” TYPE 
DEMARC. STATION BLOCK MODEM OR 
OTHER PROTECTED 
EQUIPMENT 
- -- _ 
- -- - 
- -- _ 
“66 BLOCK” 
OR RJZlX 
MDF OR CA21A 
(T) TIP 
(R) RING - -- _ 
RJ3lX 
CA318 
Figure 4-5, Typical Connection Configuration 
Figure 4-6, W-232 Interface Connector (Viewed from outside Dialer) 
pllJl SIGNAL 
1 FRAME GND 
2 
RxD (Signal in) 
3 
TxD (Signal Out) 
4,5 TIED TOGETHER 
6,8,20 TIED TOGETHER 
7 GND 
Page 18  

SECTION MITL8350-048-100-NA 
Figure 4-7, USOC RJ31WCA31A Jack and Cable Assy. 
Page 19  

SECTION MITL8350-048-l OO-NA 
procedure: 
1) 
2) 
3) 
4) 
5) 
6) 
7) 
4.12 This completes the mechanical installation of the SMarT-1’” 
Security Access Controller. Continue by programming the unit 
from the terminal.  Refer to Figure 4-3. Connect a suitable Earth Ground to the 
screw mount 
[Al provided on the connector panel. This connec- 
tion MUST be made for the unit to function properly. 
Plug the Power Pack jack into the Controller power connection 
[Bl. 
Plug the Power Pack AC line cord into a...

SECTION MITL8350-048-100-N/I 
ORDERING INFORMATION 
4.15 Table 4-l on the following page lists the part numbers and 
descriptions of items that can be ordered from MITEL DATA- 
COM INC. 
Table 4-1, SMarT-1 tm Ordering Information 4-1, SMarT-1 Ordering Information 
PART NO. 
8350-007 SMarT-1’“: DESCRIPTION 
4 Line Security Access Controller. Includes Power Pack, 
RJ31 Cables, and Mounting Hardware. 
8350-008 SMarT-1 tm: 2 Line Security Access Controller. Includes Power Pack, 
RJ31 Cables, and Mounting...

SECTION MITL8350-048-l OO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 22  

SECTION MITL8350-048-IOO-NA 
5. OPERATING DESCRIPTION 
SECURITY 
5.01 
The primary function of the SMarT-1’” Security Access Control- 
ler (SAC) is to provide security to connected systems such as 
Modems and to protect these systems from unauthorized telephone 
access. The security provided by the SAC lies in three distinct areas. 
These areas are: 
l The use of optional progress tones, or lack thereof, to make it 
difficult for an unauthorized caller to recognize that there is 
protected equipment...

SECTION MITL8350-048-IOO-NA 
5) 
6) 
internal memory, the Controller drops the line (hangs up) and 
may optionally “busy out” that particular line for a program- 
mable length of time. The unsuccessful password will be print- 
ed in the Call Detail Record. 
If an exact match for the password is found in the SAC internal 
memory, the Controller will check for the type of access that 
the password permits, including the time-of-day period as- 
signed for that particular access. 
Upon verification of a...

SECTION MlTL8350-048-l OO-NA 
during the allowed time-of-day, there will be no record 
of the call with the exception of the time and duration of 
the access and the optional printing of the successful 
password. 
DETAILED OPERATING DESCRIPTION 
With Modems 
5.05 
The following assumptions are taken into consideration when 
describing the detailed operating procedures that will follow in 
paragraph 5.06: 
1) 
2) 
3) There are correctly installed and known functional Modem con- 
nections for the Central...

SECTION MITL8350-048-IOO-NA 
4) 
5) 
6) 
7) 
Note: 
originate mode (waiting for answer tone) for a period of time 
long enough to allow the callback to occur, as previously 
mentioned. In this case, the callback could be automatically 
answered by the Modem that is accessing the host system. 
These events depend upon the sophistication of the Modems 
and the ingenuity of the user. 
After a programmable period of time, the SAC will drop the line. 
The SAC will reseize the line if the password is valid,...