Minolta magicolor 2200 User Manual

							Replacing the Fuser Unit and Transfer Roller Kit 21
Replacing the Fuser Unit
1Turn off the printer.
2Open the printer’s top cover.
3Rotate the two fuser oil roller lock levers to 
release the fuser oil roller.
4Remove the fuser oil roller.
Hold it by the green handle only.
5Place the fuser oil roller on a table or level surface.
Attention
Since the fuser oil roller removed here is to be 
installed in the new fuser unit, handle it with care. 
If you set the fuser oil roller on the table do it as 
shown in the illustration. Do not allow the roller 
surface to contact the table or get dirty. This could 
lower image quality.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Unit and Transfer Roller Kit 22
6Turn the release levers (front, rear) to 
release the fuser unit.
7Holding the fuser unit handles, 
lift up the unit.
5Dispose of it properly according 
to your local regulations.
8Remove the new fuser from its 
shipping box.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Unit and Transfer Roller Kit 23
9Carefully lower the new fuser unit so that the two pins in the fuser unit installation 
section go into the two installation holes in the fuser unit.
10Press in on the fuser unit release levers cand 
rotate them downward 
d.
This secures the fuser unit.
Attention
If the fuser unit release levers are not set correctly, the fuser oil roller cannot be 
installed. Set the fuser unit release levers to the fixed position.
1
1
1
2
2
1
1
2
2
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Unit and Transfer Roller Kit 24
11Reinstall the fuser oil roller (removed 
in step 4).
12Rotate the two oil roller levers to lock 
the oil roller into place.
13Close the printer’s top cover.
Check the release button to make sure the top cover is properly closed.
Replacing the Transfer Roller Unit 
5If there is media in the multipurpose tray, remove it. Close the multipurpose tray.
1Press the right cover release button and care-
fully open the right cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Unit and Transfer Roller Kit 25
2Holding the two transfer roller unit handles, 
remove the transfer roller unit.
5Dispose of it properly according to your local 
regulations.
3Remove the new transfer roller unit from the 
fuser kit box.
Attention
Do not touch the surface of the transfer 
roller unit. This could lower image quality.
4Place the new transfer roller unit on a 
level surface.
5Lift up the two transfer roller unit handles. 
6Holding the two transfer roller unit handles, care-
fully lower it so the transfer roller unit shaft goes 
into the two transfer roller unit installation 
guides.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Oil Roller 26
7Lower the two transfer roller unit handles.
8Carefully close the right cover. 
Check the release button status to make sure 
the cover is properly closed.
9If necessary, reopen the multipurpose tray 
and put the media back in.
Replacing the Fuser Oil Roller 
The fuser oil roller provides a lubricant for the printer via an oil-impregnated roller. This 
oil is necessary for the proper functioning of the printer.
WARNING!
The fuser unit is hot. When the top cover is opened, the fuser unit temperature 
drops gradually (one hour wait time). Do not replace the fuser oil roller until you 
are sure that the fuser unit has cooled down. 
When the fuser oil roller is worn out, the message “REPLACE OIL ROLLER
” appears 
and the printer does not print. Replace the fuser oil roller. After the new roller is installed, 
printing automatically resumes. 
5When you replace the fuser oil roller after a REPLACE OIL ROLLER
 message 
displays in the message window, the printer automatically recovers.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Fuser Oil Roller 27
1Turn off the printer.
2Open the printer’s top cover.
3Rotate the two fuser oil roller lock levers to 
release the fuser oil roller.
5Dispose of it properly according to your local 
regulations.
4Remove the new fuser oil roller from its 
shipping box.
Attention
If you set the new fuser oil roller on a table, do it as shown in 
the illustration. Do not allow the roller surface to contact the 
table or get dirty. This could lower image quality.
5Insert the new fuser oil roller 
installation guides (front, rear) 
into the fuser unit installation 
rail.
6Carefully lower the roller. 
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Transfer Belt 28
7Rotate the two oil roller levers to lock the oil 
roller into place. 
Attention
If the two fuser oil roller release levers are 
not correctly set, the top cover cannot be 
closed. Set the release levers to the roller 
fixed position.
8Carefully close the top cover.
Check the release button to make sure the 
top cover is properly closed.
9Turn on the printer.
Replacing the Transfer Belt 
When the transfer belt is at its end of life, the message “REPLACE
 TRANSFER
 BELT
” 
appears, and the printer does not print. Replace the transfer belt. After the new transfer 
belt is installed, printing automatically resumes. 
1Open the printer’s front cover.
2Remove the waste toner pack.
3Rotate the left transfer belt lock lever.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Transfer Belt 29
4Remove the OPC drum cartridge and set it 
aside.
Attention
The OPC drum is extremely sensitive to bright light and direct sunlight. Always 
put it in its protective bag until you’re ready to reinstall it. Any exposure to 
light should be avoided, or permanent damage could result. 
Also, handle the cartridge carefully by its sides so you don’t touch the surface 
(the green part) of the drum. The drum is also extremely sensitive to hand oils 
and scratches, both of which reduce print quality.
5Rotate the left lever to its 4 o’clock posi-
tion.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing the Transfer Belt 30
6Grasp the handles of the transfer belt and remove it.
5Dispose of it properly according to your local regulations.
7Remove the new transfer belt from its packag-
ing and insert it into the printer.
8Press on the transfer belt front handle with 
one hand, take the handle of the transfer belt 
fixture with your other hand, and pull the fix-
ture straight toward you.
5Dispose of it properly according to your 
local regulations.
Downloaded From ManualsPrinter.com Manuals