Lucent Technologies TransTalk 9000 Digital Wireless System MDW 9030P Wireless Pocketphone Installation And Use Manual

Using the MDW 9030P Pocketphone  3-3
ON
Column and Select Buttons Column and Select ButtonsColumn and Select Buttons Column and Select Buttons
Column and Select Buttons
The MDW 9030P Pocketphone can display the status of up to 12 lines or programmable/
intercom/drop buttons; however, it has only 4 selection buttons (the Column buttons).  The
Select button (
) is used in conjunction with the Column buttons () to increase the
available selections to 12.  Each Column button (
) affects one of the three...

3-4   Using the MDW 9030P Pocketphone
Handset Display Handset DisplayHandset Display Handset Display
Handset Display
The MDW 9030P Pocketphone display has one 16-alphanumeric-character line, and four
lines of icons to provide you with status information.
Note: Note:Note: Note:
Note:
This illustration is intended to show you what all of the indicators look like, but you will
never see all of the line status indicators illuminated at once.
1This line of the display gives you the information you would see...

Using the MDW 9030P Pocketphone  3-5 Display Messages Display MessagesDisplay Messages Display Messages
Display Messages
The top line of the handset display uses up to 16 alphanumeric characters to provide
messages such as the following:
nLCL:P (or LCL:D, LCL:M1, or LCL:M2) indicates that the handset is in Local Mode, and
tells which communications system the button mapping is set to emulate:
LCL:PPARTNER systems
LCL:DDEFINITY systems, System 25, System 75, and System 85
LCL:M1All MERLIN systems (except...

3-6   Using the MDW 9030P PocketphoneRange Indicators Range IndicatorsRange Indicators Range Indicators
Range Indicators
For maximum range and voice quality, always fully extend the antenna before placing or
answering a call.  The antenna must be either fully retracted (for short range) or fully
extended (for maximum range) to use the Pocketphone.
The handset provides an audible and a visual signal to alert you when the handset is near
the end of the range of the radio module. Depending on how far away...

Using the MDW 9030P Pocketphone  3-7
3
4
2
1
Volume Control Volume ControlVolume Control Volume Control
Volume Control
To increase or decrease the volume of the handset alerter or the receiver (earpiece):
nAlerter:  Press the “+” or the “–” button while the MDW 9030P is awake but turned off.
If the display is dark (the phone is in sleep mode), press 
 to wake it up, then press
the “+” or the “–” button.
nReceiver:  Press the “+” or the “–” button while the MDW 9030P is turned on.
Carrying Your...

3-8   Using the MDW 9030P Pocketphone
Antenna AntennaAntenna Antenna
Antenna
The MDW 9030P Pocketphone comes with a user-replaceable, flexible, retractable antenna.
For maximum range and voice quality, always fully extend the antenna before placing or
answering a call.  You can receive a call (if you are within range of the radio module) without
extending the antenna, but you may get a RANGE indication.  The antenna must be fully
extended for optimal performance.
Changing the Handset Settings Changing...

Using the MDW 9030P Pocketphone  3-9 Enabling or Disabling the Vibrator Enabling or Disabling the VibratorEnabling or Disabling the Vibrator Enabling or Disabling the Vibrator
Enabling or Disabling the Vibrator
The vibrator vibrates to alert you to an incoming call in situations where you do not want to
disturb others with an audible ring. You can enable or disable the vibrator using the follow-
ing procedure:
1. Make sure the handset is turned off.
2. Press and hold the Select button (
) for three...

3-10   Using the MDW 9030P Pocketphone
To enable Line Preselection, use the following procedure:
1. Make sure the handset is turned off.
2. Press and hold the Select button (
) for three seconds.
3. While still holding 
, press O.
The handset beeps twice, and the display shows the handset settings, indicating you
are in Local Mode.  (While in Local Mode, the MDW 9030P can still receive notification
of incoming calls.)
If Line Preselection is enabled, PSEL shows on the top line of the display.  For ex-...

Using the MDW 9030P Pocketphone  3-11 Enabling or Disabling the Alerter Enabling or Disabling the AlerterEnabling or Disabling the Alerter Enabling or Disabling the Alerter
Enabling or Disabling the Alerter
The alerter is an audible signal to notify you of an incoming call. If a call comes in while the
phone is idle, the handset rings. If you are already on a call, the handset chirps softly. You
can adjust the volume of the alerter by pressing the + button or the – button on the side
of the handset when...

3-12   Using the MDW 9030P Pocketphone
Test Modes Test ModesTest Modes Test Modes
Test Modes
You can use Local Test Mode and Wireless Test Mode to verify that your handset is
working properly and that the MDW 9030P system is performing optimally.
Using Local Test Mode Using Local Test ModeUsing Local Test Mode Using Local Test Mode
Using Local Test Mode
You can use Local Test Mode to activate the audio warning signal, the vibrator, and all
visual indicators on the handset display, enabling you to test...