Lucent Technologies TransTalk 9000 Digital Wireless System MDW 9030P Wireless Pocketphone Installation And Use Manual

Installing the MDW 9030P Pocketphone
          
  2-19
6Insert a telephone line cord into the bottom of
each radio module.
Slide the telephone line cords through the rear
exit slots on the bottom of the carrier. Cords
originating from Modules 1 and 6 can share exit slots
with cords from Modules 2 and 5 respectively.
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULE
MUSIC
ON
HOLDVOL
PAGE
E...

2-20
              
   Installing the MDW 9030P Pocketphone
12
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T
 O
F
 S
Y
N
C
OUT
OUT OF SYNC
Verify that the carrier’s Out of Sync LED is not
lit. If the LED is lit, power down and then
repower the carrier. If the LED is still lit, follow the
suggestions in the Installation Problems section of
Chapter 5, Troubleshooting. If the LED is still lit, call
for help as described on the inside front...

Installing the MDW 9030P Pocketphone
          
  2-21
Installing a Single Carrier on a Wall Installing a Single Carrier on a WallInstalling a Single Carrier on a Wall Installing a Single Carrier on a Wall
Installing a Single Carrier on a Wall
nInstall high on wall, leaving 6–12 inches (15.2–30.5 cm) between antennas and
ceiling
nNever install or remove a radio module from a carrier that is plugged into a wall
outlet (hot insertion)
nSee “Key Components” earlier in this chapter for additional picture...

2-22
              
   Installing the MDW 9030P Pocketphone
 When the card edge is fully seated, a snap
lock on the bottom of the radio module will
engage.
Insert a telephone line cord into the bottom of
each radio module.6
7
Slide the telephone line cords through the cable
manager slot on the left front of the carrier.
Starting from the leftmost slot (#1), insert each
radio module into the carrier by hooking it onto
the radio module mounting rod. Slowly swing the radio
modules card edge into the card...

Installing the MDW 9030P Pocketphone
          
  2-23
12
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T O
F
 S
Y
N
C
OUT
OUT OF SYNC
Verify that the carrier’s Out of Sync LED is not
lit. If the LED is lit, power down and then
repower the carrier.  If the LED is still lit, follow the
suggestions in the Installation Problems section of
Chapter 5, Troubleshooting. If the LED is still lit, call
for help as described on the inside front...

2-24
              
   Installing the MDW 9030P Pocketphone
Installing Multiple Carriers Installing Multiple CarriersInstalling Multiple Carriers Installing Multiple Carriers
Installing Multiple Carriers
nInstall each carrier high on wall, leaving 6–12 inches (15.2–30.5 cm) between
antennas and ceiling
nInstall each carrier 1 foot (0.3 m) optimal to 4 feet (1.2 m) from its
neighboring carrier
nNever install or remove a radio module from a carrier that is plugged into a wall
outlet (hot insertion)
nSee...

Installing the MDW 9030P Pocketphone
          
  2-25
Remove the plastic cap covering each radio
module’s card edge before inserting the radio
modules into the carriers.94
6
CAUTION
IN
OUT
OUT OF SYNC
Connect an expansion cable to the OUT jack of
the control carrier.
CAUTION
IN
OUT
OUT OF SYNC
From
Control
Carrier
Insert the free end of the expansion cable into
the IN jack of the expansion carrier immedi-
ately to the right of the control carrier.
NOTE: NOTE:NOTE: NOTE:
NOTE:
Although installing an...

2-26
              
   Installing the MDW 9030P Pocketphone
Working from left to right, insert a radio module
into each slot of the control carrier, starting with
Slot 1; hook each radio module onto a mounting rod.
Slowly swing the radio modules card edge into the
card edge connector on the back of the carrier.
IMPORTANT: IMPORTANT:IMPORTANT: IMPORTANT:
IMPORTANT:
Slot 6 of a carrier that has another carrier to the
right of it must always contain a radio module
to pass the synchronization signal to the...

Installing the MDW 9030P Pocketphone
          
  2-27
Plug an AC adapter cord into the left side of
each carrier.16
12345
12N O
Insert each carrier’s power cord into its AC
adapter.
If appropriate, you can wall-mount each AC adapter
using its attached wall-mounting bracket.17
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULE
MUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S...

2-28
              
   Installing the MDW 9030P Pocketphone
If the carriers are plugged into... Then...
one surge suppressor strip power the strip.
Result: All carriers will turn on simultaneously.
wall outlets plug in the power for all carriers in this order:
Plug each carrier’s power cord into one of the
following power sources that is not controlled
by an on/off switch:
nProperly grounded 3-prong wall outlets
nSurge suppressor strip
Power the carriers as follows:
18
Go to “Installation Self-Test.”...