Lucent Technologies TransTalk 9000 Digital Wireless System MDW 9030P Wireless Pocketphone Installation And Use Manual

							Installing the MDW 9030P Pocketphone
          
  2-19
6Insert a telephone line cord into the bottom of
each radio module.
Slide the telephone line cords through the rear
exit slots on the bottom of the carrier. Cords
originating from Modules 1 and 6 can share exit slots
with cords from Modules 2 and 5 respectively.
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULE
MUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
SInsert the free end of the telephone line cord
into the appropriate extension jack or terminal/
station connector on your communications system
switch/control unit (refer to your communications
system manual for the proper location).8
7
5When the card edge is fully seated, a snap lock on
the bottom of the radio module will engage. 
						

							2-20
              
   Installing the MDW 9030P Pocketphone
12
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T
 O
F
 S
Y
N
C
OUT
OUT OF SYNC
Verify that the carrier’s Out of Sync LED is not
lit. If the LED is lit, power down and then
repower the carrier. If the LED is still lit, follow the
suggestions in the Installation Problems section of
Chapter 5, Troubleshooting. If the LED is still lit, call
for help as described on the inside front cover of this
book.
Go to “Installation Self-Test.”
Place the carrier on its feet towards the back of
the shelf or desk, making sure it is in a stable
position. Be sure the telephone line cords come out the
rear exit slots in the back of the unit. Arrange the power
cord and telephone line cords beneath the shelf or
desk so no one can step on them or trip over them.
11Insert the carrier’s power cord into the AC
adapter, then plug the power cord into a
properly grounded 3-prong wall outlet that is not
controlled by an on/off switch.
If appropriate, you can wall-mount the AC adapter
using its attached wall-mounting bracket.
!CAUTION:
Never connect or disconnect telephone line
cords, or insert or remove radio modules,
while the carrier is plugged into the wall outlet. Insert the carrier’s AC adapter cord into the left
side of the carrier.
9
12345
12N O
10 
						

							Installing the MDW 9030P Pocketphone
          
  2-21
Installing a Single Carrier on a Wall Installing a Single Carrier on a WallInstalling a Single Carrier on a Wall Installing a Single Carrier on a Wall
Installing a Single Carrier on a Wall
nInstall high on wall, leaving 6–12 inches (15.2–30.5 cm) between antennas and
ceiling
nNever install or remove a radio module from a carrier that is plugged into a wall
outlet (hot insertion)
nSee “Key Components” earlier in this chapter for additional picture detail
Perform the tests described in Wireless Test
Mode earlier in this chapter to determine the
optimal placement of the radio module. To perform
the tests, all you need is an electrical outlet for the
radio module and a charged battery pack in the
handset.
1
2Check to make sure the carrier’s power cord is
unplugged from the wall outlet before continuing.
Remove the plastic cap covering each radio
module’s card edge before inserting the radio
modules into the carrier.
4
Place the carrier against the wall. Choose a loca-
tion backed by a wooden stud (if unavailable, use
toggle bolts instead of the supplied wood screws). Hold
the carrier straight; use a level if needed. Using a nail or
pencil, mark screw locations through the four wall-mount
holes.
Start the screws, leaving the screw heads protruding
approximately 
1/2 (12 mm) from the wall. Place the car-
rier assembly over the screws, then slide it downward to
lock it into place. Tighten the screws.
3
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE ONLY
AT&T CABLE
P⁄ N 847667896IN
OUT
OUT OF SYNC 
						

							2-22
              
   Installing the MDW 9030P Pocketphone
 When the card edge is fully seated, a snap
lock on the bottom of the radio module will
engage.
Insert a telephone line cord into the bottom of
each radio module.6
7
Slide the telephone line cords through the cable
manager slot on the left front of the carrier.
Starting from the leftmost slot (#1), insert each
radio module into the carrier by hooking it onto
the radio module mounting rod. Slowly swing the radio
modules card edge into the card edge connector on
the back of the carrier.5
8 
						

							Installing the MDW 9030P Pocketphone
          
  2-23
12
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T O
F
 S
Y
N
C
OUT
OUT OF SYNC
Verify that the carrier’s Out of Sync LED is not
lit. If the LED is lit, power down and then
repower the carrier.  If the LED is still lit, follow the
suggestions in the Installation Problems section of
Chapter 5, Troubleshooting. If the LED is still lit, call
for help as described on the inside front cover of this
book.
Go to “Installation Self-Test.”
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULE
MUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
SInsert the free end of each telephone line cord
into the appropriate extension jack or terminal/
station connector on your communications system
switch/control unit (refer to your communications
system manual for the proper location).
11Insert the carrier’s power cord into the AC
adapter, then plug the power cord into a
properly grounded 3-prong wall outlet that is not
controlled by an on/off switch.
If appropriate, you can wall-mount the AC adapter
using its attached wall-mounting bracket.
!CAUTION:
Never connect or disconnect telephone line
cords, or insert or remove radio modules,
while the carrier is plugged into the wall outlet.
12345
12N O
Plug the carrier’s AC adapter cord into the left
side of the carrier.
9
10 
						

							2-24
              
   Installing the MDW 9030P Pocketphone
Installing Multiple Carriers Installing Multiple CarriersInstalling Multiple Carriers Installing Multiple Carriers
Installing Multiple Carriers
nInstall each carrier high on wall, leaving 6–12 inches (15.2–30.5 cm) between
antennas and ceiling
nInstall each carrier 1 foot (0.3 m) optimal to 4 feet (1.2 m) from its
neighboring carrier
nNever install or remove a radio module from a carrier that is plugged into a wall
outlet (hot insertion)
nSee “Key Components” earlier in this chapter for additional picture detail
Perform the tests described in Wireless Test
Mode earlier in this chapter to determine the
optimal placement of the radio module. To perform
the tests, all you need is an electrical outlet for the
radio module and a charged battery pack in the
handset.
1
2Check to make sure the carrier’s power cord is
unplugged from the wall outlet before continuing.
3Choose a location backed by a wooden stud for
the carrier (if unavailable, use toggle bolts
instead of the supplied wood screws).
IMPORTANT: IMPORTANT:IMPORTANT: IMPORTANT:
IMPORTANT:
The leftmost carrier must be the control carrier.
See Setting the Control/Expansion DIP Switch
earlier in this chapter.
Place the carrier against the wall, leaving enough
room to the right for additional carrier(s) if applicable.
Hold the carrier straight; use a level if needed. Using a
nail or pencil, mark screw locations through the four
wall-mount holes. Start the screws, leaving the screw
heads protruding approximately 
1/2 (12 mm) from the
wall.
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
47
667896IN
OUT
OUT OF SYNC
4
Repeat Steps 1 through 3 for each carrier.
Place the carrier over the screws, then slide it
downward to lock it into place. Be sure that the
leftmost carrier is the control carrier. Tighten the
screws. Repeat for each carrier.
5
4 
						

							Installing the MDW 9030P Pocketphone
          
  2-25
Remove the plastic cap covering each radio
module’s card edge before inserting the radio
modules into the carriers.94
6
CAUTION
IN
OUT
OUT OF SYNC
Connect an expansion cable to the OUT jack of
the control carrier.
CAUTION
IN
OUT
OUT OF SYNC
From
Control
Carrier
Insert the free end of the expansion cable into
the IN jack of the expansion carrier immedi-
ately to the right of the control carrier.
NOTE: NOTE:NOTE: NOTE:
NOTE:
Although installing an expansion cable
into the wrong IN or OUT jack will not harm either
carrier, doing so causes all handsets to work
improperly and the Out of Sync LED to light.7
8If you have a second expansion carrier:
a. Connect an expansion cable to the OUT jack
of expansion carrier #1.
b. Insert the free end of the expansion cable
into the IN jack of expansion carrier #2.
See “Key Components” earlier in this chapter for an
illustration of a three-carrier setup. 
						

							2-26
              
   Installing the MDW 9030P Pocketphone
Working from left to right, insert a radio module
into each slot of the control carrier, starting with
Slot 1; hook each radio module onto a mounting rod.
Slowly swing the radio modules card edge into the
card edge connector on the back of the carrier.
IMPORTANT: IMPORTANT:IMPORTANT: IMPORTANT:
IMPORTANT:
Slot 6 of a carrier that has another carrier to the
right of it must always contain a radio module
to pass the synchronization signal to the next
carrier.
When the card edge is fully seated, a snap lock
on the bottom of the radio module will engage.11
12Repeat Steps 10 and 11 for each expansion
carrier, until each radio module is inserted into
a carrier.
NOTE: NOTE:NOTE: NOTE:
NOTE:
Fill all six slots of the current carrier before
inserting radio modules into the next carrier.
Insert a telephone line cord into the bottom of
each radio module.13 10 
						

							Installing the MDW 9030P Pocketphone
          
  2-27
Plug an AC adapter cord into the left side of
each carrier.16
12345
12N O
Insert each carrier’s power cord into its AC
adapter.
If appropriate, you can wall-mount each AC adapter
using its attached wall-mounting bracket.17
MODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
SMODULE206
PFT
PFTE
X
T
E
N
S
I
O
N
SL
I
N
E
S
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
S
MODULE400
PFTL
I
N
E
SPROCESSOR
MODULE
MUSIC
ON
HOLDVOL
PAGE
E
X
T
E
N
S
I
O
N
SE
X
T
E
N
S
I
O
N
S
SMDR
MUSIC
ON
HOLD
N
S
I
O
N
SX
T
E
N
S
I
O
N
S15Insert the free end of the telephone line cord
into the appropriate extension jack or terminal/
station connector on your communications system
switch/control unit (refer to your communications
system manual for the proper location).
14Slide the telephone line cords through the
cable manager slot on the left front of each
carrier. 
						

							2-28
              
   Installing the MDW 9030P Pocketphone
If the carriers are plugged into... Then...
one surge suppressor strip power the strip.
Result: All carriers will turn on simultaneously.
wall outlets plug in the power for all carriers in this order:
Plug each carrier’s power cord into one of the
following power sources that is not controlled
by an on/off switch:
nProperly grounded 3-prong wall outlets
nSurge suppressor strip
Power the carriers as follows:
18
Go to “Installation Self-Test.”
19Verify that the carriers’ Out of Sync LEDs are
not lit. If an LED is lit, power down and then
repower the carriers as described in Step 18. If the
LED is still lit, follow the suggestions in the Installa-
tion Problems section of Chapter 5, Troubleshoot-
ing. If the LED is still lit, call for help as described on
the inside front cover of this book.
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONU
S
E
 O
N
L
Y
A
T
&
T
 C
A
B
L
E
P
⁄N
 8
4
7
6
6
7
8
9
6IN
O
U
T
O
U
T
 O
F
 S
Y
N
C
OUT
OUT OF SYNC
!CAUTION:
Never connect or disconnect expansion cables or telephone line
cords, or insert or remove radio modules, while the carrier is
plugged into the wall outlet.
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE ONLY
AT&T CABLE
P⁄ N 847667896IN
OUT
OUT OF SYNC
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE ONLY
AT&T CABLE
P⁄ N 847667896IN
OUT
OUT OF SYNC
12346
4TRANSTALK
2 1O   N2 1O   N
5
CAUTIONUSE ONLY
AT&T CABLE
P⁄ N 847667896IN
OUT
OUT OF SYNC
Control
Carrier
1
Expansion
Carrier #1Expansion
Carrier #2
23