Lucent Technologies Octel 100 Implementation And Service Manual

5. Preparing the Hardware
Implementation and Service ManualIns talling Ferrite Bead Cable Clamps5-9
To install the voice and fax boards:
1.  Turn off the power to the PC and any peripherals.
2. Unfasten the screws retaining the PC’s cov er and remov e the cov er.
3.  Select an expansion slot in which to install the board. Use an 8- or 16-bit slot for the
Dialogic DIALOG/4, D/4xD, D/42-SL, D/42-SX, and D/42-NS boards. Use a 16-bit
slot for the Brooktrout fax boards.
4.  Unfasten the screw retaining the...

5. Preparing the Hardware
Implementation and Service ManualIns talling Ferrite Bead Cable Clamps5-10
Installing the Ferrite Bead Cable Clamps on 2-Cable Boards
W hen installing the ferrite bead cable clamps on 2-cable boards, a separate clamp is used
on each cable. Refer to the following illustration when installing the ferrite bead cable.
To install the ferrite bead cable clamp on the Dialogic D/42D-SX or Brooktrout TruFax
board cable:
1.   Locate the phone cable, as labeled in the illustration.
2....

5. Preparing the Hardware
Implementation and Service ManualConnecting the Telephone Lines5-11
4.   Place two cable ties, one on either side of the ferrite cable clamp, around the four
cables to ensure that the clamp stays in place, as shown in the illustration.
5.   Plug the phone cables into the phone jacks on the v oice board. See the following
topic, “Connecting the Telephone Lines.”
Connecting the Telephone Lines
After you install the v oice boards, you must connect them to the switch. The method of...

5. Preparing the Hardware
Implementation and Service ManualConnecting the Fax Lines5-12
·  The system deliv ers a fax retriev ed from a V-Tree.
  Non-Transfer Method – Denotes a situation where v oice and fax channels share
telephone extensions. Using this method, both v oice and fax transmission and reception
occur on the same line.
  Consult the Configuration Note for the phone system to determine whether a specific
method is required to connect the fax board to the switch. For additional information,...

5. Preparing the Hardware
Implementation and Service ManualConnecting the Fax Lines5-13
  The following diagram represents a sample wiring configuration for the Transfer method.
In the sample diagram, the v oice board and the switch use RJ-14s, while the fax port
uses RJ-11 connectors. In this case a splitter must be used to connect the two RJ-11
lines from the fax board to the switch.
 
  Connecting TruFax Boards for the Non-Transfer Method
  Consider the following when connecting TruFax boards for the...

5. Preparing the Hardware
Implementation and Service ManualInstalling the Sentinel5-14
 Installing the Sentinel
  The sentinel shipped with the messaging system controls:
·  System software v ersion access
·  Access to optional modules such as OctelNet™, AIM, Visual Mailbox, and the
Visual Architect™ Toolkit
·  System copy protection
All messaging system sentinels are assigned a unique serial number, which identifies the
system and allows you to perform certain upgrades using the Sentinel Upgrade...

5. Preparing the Hardware
Implementation and Service ManualConfiguring the IBM V.90 PCI Data/Fax Modem5-15
Configuring the IBM V.90 PCI Data/Fax Modem
The IBM V.90 PCI data/fax modem is an internal modem supported for use with the
messaging system. This modem is preconfigured on new systems. Use the following
instructions if you have to reinstall the operating system.
To install and configure the modem’s device driver:
1.  Shut down the messaging system if it is currently running.
2.  Shut down the PC:...

5. Preparing the Hardware
Implementation and Service ManualConfiguring the IBM V.90 PCI Data/Fax Modem5-16
e.  Use the right arrow key to select Not av ailable.
f.  Press  to exit the Interrupt Resources screen. The ISA Legacy Resources
screen displays.
6.  Press  to exit the ISA Legacy Resources screen. The Configuration/Setup
Utility screen displays.
7.  Use the down arrow to highlight Sav e Settings and press .
8.  W hen prompted, press  to confirm that you want to sav e the settings.
9.  Press  to...

5. Preparing the Hardware
Implementation and Service ManualInstalling the Tape Backup Unit (Optional)5-17
21.  Shut down the PC:
a.  Click the right mouse button on an empty area of the OS/2 desktop and select
Shut down from the menu that displays.
b.  W hen you are prompted whether you want to close all windows and activ e
programs, click OK.
c.  When prompted to shut down or reboot, press  to reboot the
PC.
Installing the Tape Backup Unit (Optional)
The Iomega Ditto is an optional tape backup drive...

5. Preparing the Hardware
Implementation and Service ManualInstalling the Tape Backup Unit (Optional)5-18
Connecting the External Ditto Tape Drive Hardware
The following procedure outlines the general steps for connecting the Ditto tape drive in
the computer.
To install the external tape backup hardware:
1.  Shut down the messaging system and turn off the computer.
2. If a printer is currently attached to the sentinel on the PC’s parallel port, unplug it.
3.
 Connect the female end of the parallel cable...