Lucent Technologies GuestWorks Issue 6 Technician Handbook

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
31 Connecting the Hospitality Adjuncts 
Switch-to-INTUITY Admin Link (Mode Code
Integration)
When using Mode Code Integration, the administrative link between the switch 
and the MAP (the link that transfers information to support the INTUITY AUDIX 
service for office staff voice messaging) connects by way of an analog port on the 
switch and a voice port on the MAP. This connection is the same as the voice...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
32 Connecting the Hospitality Adjuncts 
Switch-to-INTUITY Voice Port Connections
This connection is used for the following:
nFor callers leaving messages for guests and office staff
nFor guests and office staff to call the INTUITY system to retrieve their voice 
messages
nFor the administrative link between the switch and the MAP when using 
Mode Code Integration (see Pag e 31
).
Parts List
nOne or more...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
33 Connecting the Hospitality Adjuncts 
Use the 885A connecting block label to record the extension numbers of 
the voice ports connected to the MAP.
nFerrites (one for each voice line) (comcode 407616846)
Ferrites are required for installation in some countries. See 
INTUITY Mes-
saging Solution Release 4 Supplement for Technicians 
for more informa-
tion.
n103A modular connecting blocks (one for each voice...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
34 Connecting the Hospitality Adjuncts 
Figure 7.  IVC6 and IVC6A Tip/Ring Card Switch Settings
8-pin
modular
jacks
Audio
input
Audio
output
TDM bus
terminator SIPs
Rocker
switches
(see IVC6
switch setting
figure)
Base I/O address = 100 Hex.
IVC6 T/R 0
First card installedBase I/O address = 200 Hex.
IVC6 T/R 1
Second card installedBase I/O address = 300 Hex.
IVC6 T/R 2
Third card installed
Base I/O address =...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
35 Connecting the Hospitality Adjuncts 
Figure 8.  NGTR Tip/Ring Card Switch Settings
ngtr KLC 070296
I/O address switch
TDM bus B
TDM bus A TDM bus terminator SIPs
8-pin
modular
jacks
Audio
output Audio
input 

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
36 Connecting the Hospitality Adjuncts 
Cabling Diagram
Figure 9 shows the connections between analog circuit pack ports on the switch 
and a Tip/Ring card on the MAP.
Figure 9.  Switch-to-INTUITY Voice Port Connections 

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
37 Connecting the Hospitality Adjuncts 
INTUITY Lodging-to-PMS Link
This connection is used to activate and deactivate guest voice messaging mail-
boxes when guests check-in and check-out.
NOTE:
If the Switch/INTUITY/PMS Link Integration feature is used, this connection 
is not required. See “
INTUITY Lodging-to-PMS Translations” on Page 190 
for more information about this feature. If Mode Code Integration is...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
38 Connecting the Hospitality Adjuncts 
Cabling Diagram
Figure 10 shows the connection used for controlling guest mailboxes between the 
MAP and the PMS.
NOTE:
For some installations, this connection at the MAP is made to COM1 
instead of the Multi-Port Serial Card. If this is the case at your site, do not 
use the D6AP modular cord or Equinox adapter. Plug the Null Modem 
directly into COM1.
Figure 10. INTUITY...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
39 Connecting the Hospitality Adjuncts 
Test Procedure
Using the RS232 Mini-Tester (see the Note on Pa ge 1 1), check the status of the 
link where the Equinox adapter connects to the null modem as shown in 
Figure 10
. The leads marked with an asterisk are controlled by the INTUITY sys-
tem, and the PMS controls the other leads. Translations for this connection begin 
on Page 190
.
!CAUTION:
After using a...

GuestWorks Issue 6 Technician Handbook  555-231-109  Issue 1
April 2000
Installing the System 
40 Connecting the Hospitality Adjuncts 
With the mini-tester connected to the MAP and the PMS, but in an idle state, the 
mini-tester should show the following:
TD*
RTS*
DTR* RD
CTS
DSR
CD
dark
red
greenred red
red
red