Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-19 Add the Fiber Optic Cable 
6
Figure 6-10. Replace the Fan Cover
13. Connec t the fib er c ab le to the ang led  c onnec tor on the front of the c irc uit 
pack. See Figure 6-11
.
lcda5fop EWS 110398
ENTER
/YES ENTER
/YES NEXT
/NO NEXT
/
NO BACK
BACK
AUDIX
AUDIXBOOT/
SHUTDOWN BOOT/
SHUTDOWN
ALARMS
EMER TR EMERTR 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-20 Add the Fiber Optic Cable 
6
Figure 6-11. Connect Fiber Cable to Circuit Pack
14. Dress the cable using the supplied cable ties and cable tie mounts. See 
Figure 6-12
.
NOTE:
Dress the fiber optic  c able straight down the front of the circuit pack. 
Do not allow the c ab le to c ross in front of another c irc uit p ac k.
scdafo_4 KLC 051298
C12...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-21 Add the Fiber Optic Cable 
6
Figure 6-12. Dress the Cable
15. If a c irc uit p ac k was removed  to ac c ess 2 op en slots (from ‘‘Cabinet 
Preparation’’ on page 6-10), rep lac e the c irc uit p ac k into its orig inal slot.
16. Close the front d oor.
17. Discard the pass-thru tool.
Test the Installation
1. Log in to the manag ement terminal.
2....

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-22 Install a New EPN Cabinet in an Existing System 
6
Install a New EPN Cabinet in an 
Existing System
Figure 6-13 shows a typ ic al multic arrier EPN c ab inet. Eac h EPN c ab inet is 
normally p ositioned  ad jac ent to the PPN c abinet b ut may b e loc ated  remotely in 
a d ifferent room or a d ifferent b uild ing .
Figure 6-13. Typical...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-23 Install a New EPN Cabinet in an Existing System 
6
Connect Power and Ground 
1. For an AC- or DC-p owered  system, c onnec t p ower and ground  to the 
c ab inet as instruc ted  in 
DEFINITY Enterp rise Communic ations Server 
Release 8 Installation and  Test for Multic arrier Cab inets
.
2. Connec t the ap p roved  g round  to the new c abinet as...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-24 Install a New EPN Cabinet in an Existing System 
6
1. Install a 9823A lig htwave transc eiver onto Slot 1 on the rear of the PPN 
Control Carrier. See Figure 6-14
.
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to the EPN c ab inet 
easier. 
3. Route...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-25 Install a New EPN Cabinet in an Existing System 
6
Direct-Connect New EPN to Existing PPN and
EPN (Standard Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet (next to the PPN c ab inet) is c alled  Cab inet 2, and  the last EPN 
c ab inet is c alled  Cab inet 3.
1. At the rear...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-26 Install a New EPN Cabinet in an Existing System 
6
Direct-Connect New EPN to Existing PPN and
EPN (High or Critical Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet (next to the PPN c ab inet) is c alled  Cab inet 2, and  the last EPN 
c ab inet is c alled  Cab inet 3. 
1. At...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-27 Install a New EPN Cabinet in an Existing System 
6
Interconnect Cabling Release 8r 
For more fib er op tic  c ab ling information, refer to DEFINITY Enterp rise 
Communications Server Release 8 Installation and Test for Multicarrier Cabinets
.
Switch-Connect New EPN to Existing PPN and
EPN (Standard Reliability)
For the following  c onnec tion...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-28 Install a New EPN Cabinet in an Existing System 
6
Figure 6-15. Switch-Connected Release 8r with SNC in EPN
Switch-Connect New EPN to Existing PPN and
EPN (High Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet is c alled  Cab inet 2, and  the EPN c ab inet c ontaining  the...