Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-9 Add the Fiber Optic Cable 
6
LASER Product
CLASS 1 LASER PRODUCT
IEC 825 1993
The DEFINITY ECS may c ontain a Class 1 LASER devic e if sing le-mod e fib er 
op tic  c ab le is c onnec ted  to a remote Exp ansion Port Network (EPN). The LASER 
d evic e op erates within the following  p arameters:
nMaximum Power Outp ut: -5d Bm
nWaveleng th: 1310 nm...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-10 Add the Fiber Optic Cable 
6
Cabinet Preparation
1. Open the front d oor.
NOTE:
Ad ministration may b e req uired  b efore removing  the c irc uit p ac k in 
the following  step .
2. Determine which slot (1 or 2) will c ontain the new fiber optic circuit pac k. 
Remove the c irc uit p ac k or the b lanking  p late from this slot. 
NOTE:
If a c irc...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-11 Add the Fiber Optic Cable 
6
Figure 6-2. Remove the I/O Cable Connector
7. Using  a sup p lied  c able tie, sec ure the removed  I/O c onnec tor to nearb y 
c ab ling. See Figure 6-3
. Figure Notes
1. Press tab  down 2. Pull c onnec tor forward
lcda8fop RPY 021198
1
2 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-12 Add the Fiber Optic Cable 
6
Figure 6-3. Secure the I/O Cable Connector
8. From the front, remove the fan c over. See Figure 6-4
. Figure Notes
1. Tie wrap
lcda9fop RPY 0213981 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-13 Add the Fiber Optic Cable 
6
Figure 6-4. Remove the Fan Cover
lcda3fop EWS 110398
ENTER
/YES ENTER
/YES NEXT
/NO NEXT
/
NO BACK
BACK
AUDIX AUDIXBOOT/
SHUTDOWN BOOT/
SHUTDOWN
ALARMS
ALARMS
EMERTR
EMERTR 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-14 Add the Fiber Optic Cable 
6
Install the Pass-thru Kit
1. Snap  the SC-SC fib er op tic  adap ter on the p ass-thru tool. See Figure 6-5. 
Use the b eig e ad apter even if sing le-mod e fib er is b eing  installed . The 
SC-SC ad ap ter is b etter suited  for c ab le routing  in the next step s. 
NOTE:
If sing le-mod e fib er is being installed ,...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-15 Add the Fiber Optic Cable 
6
Figure 6-6. Insert the Pass-thru Tool
!CAUTION:
Avoid  b end ing  fib er op tic  c ab les to a rad ius smaller than 1.5 inc hes 
(3.8 c m), to p revent mec hanic al stress on the c ab les. 
!CAUTION:
During  the ac tual installation of fiber op tic  c omp onents, use either all b eig e 
or all b lue ad ap ters. Beig e...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-16 Add the Fiber Optic Cable 
6
4. Pull the tool (with ad apter and  c ab le attac hed ) out throug h the front of the 
c ab inet. See Figure 6-7
.
Figure 6-7. Fiber Optic Cable and Adapter
5. From the rear, route the fib er op tic  c ab le throug h the op ening  vac ated  b y 
the I/O c able c onnec tor.
6. If nec essary, remove the fiber ad ap ter...

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-17 Add the Fiber Optic Cable 
6
Figure 6-8. Bracket Attachments 
10. Wrap  the c ab le d isc onnec t lab el around  the fib er op tic  c ab le. See 
Figure 6-9
. Figure Notes:
1. Fiber cable
2. I/O c onnec tor ad ap ter b rac ket3. SC-SC adapter
4. SC-ST ad ap ter
lcda7fop KLC 051198
1
2
3
4
2 

DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-18 Add the Fiber Optic Cable 
6
Figure 6-9. Cable Disconnect Label
11. Close the rear door.
!CAUTION:
Avoid  b end ing  fib er op tic  c ab les to a rad ius smaller than 1.5 inc hes 
(3.8 c m), to p revent mec hanic al stress on the c ab les. Plan the use of 
c ab le ties to avoid c rimping  the c ab le or c reating  a fixed stress point 
where, at a...