Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Installation And Maintenance For Survivable Remote EPN Manual

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-19 Administer the Release 7r and SRP 
1
2. Disp lay the hard ware in the SREPN b y typ ing  display circuit-packs 
  (the port network number of the SREPN) and pressing 
En t e r.
NOTE:
The p ort network numb ers d iffer b etween the Release 7r and  the 
SRP. On the Release 7r manag ement terminal, the p ort network that 
you may b e d isp laying is 5; whereas, on the SRP management 
terminal, the p ort network that you are ad d ing  c irc uit p ac ks to is 
always 2. 
3. On the SRP manag ement terminal, typ e change circuit-packs 2
 and  
p ress 
En t e r. All the c irc uit p ac ks d isp layed  on the Release 7r manag ement 
terminal that are not Release 7r spec ific  (suc h as p ac ket g ateways or 
DS1CONV) must b e ad d ed  to the SRP. Be sure to ad d  c irc uit p ac ks to all 
nec essary c arriers.
NOTE:
Save often the information you ad d  to the SRP manag ement 
terminal.
4. Press 
En t e r.
Administering the software
1. Set the c ustomer op tions on the SRP to c losely matc h the Release 7r 
op tions.
Identify and add trunk information
Ad ministration for eac h of the c irc uit p ac ks in the SREPN need s to be ad d ed  to 
the SRP. For every trunk c irc uit p ac k, the trunk ad ministration must b e ad d ed  
and  for every p ort on every line c irc uit p ac k, the station ad ministration must b e 
added.
1. On the Release 7r management terminal, typ e list configuration 
port-network 
  (numb er of the SREPN p ort network) and  p ress 
En t e r. Id entify the slot numbers of the trunk c irc uit p ac ks.
2. For eac h trunk c irc uit p ac k on the Release 7r manag ement terminal, typ e 
display port
   (where CCSS01 is the c irc uit p ac k and  p ort 
loc ation of the first p ort on the trunk c irc uit p ac k) and  p ress 
En t e r. The Port 
Information sc reen ap pears. The Identification:
 field  shows the 
trunk g roup  and memb er information for that p ort. (For example, 98/1 
means that this p ort is memb er 1 of trunk g roup  98.)
3. Type display trunk-group
   (numb er is the trunk g roup  
memb er) and  p ress 
En t e r.
4. On the SRP manag ement terminal, typ e add trunk-group
  and 
p ress 
En t e r.  
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-20 Administer the Release 7r and SRP 
1
5. Ad d  all of the trunk group  information (d isp layed  on the Release 7r 
manag ement terminal) to the SRP management terminal. 
NOTE:
The p ort network numb ers d iffer b etween the Release 7r and  the 
SRP. On the Release 7r manag ement terminal, the p ort network that 
you may b e d isp laying is 5; whereas, on the SRP management 
terminal, the p ort network that you are ad d ing  c irc uit p ac ks to is 
always 2. 
6. The Memb er Assig nments sc reen on the Release 7r manag ement terminal 
ap p ears. Note the numb er of the memb ers in the trunk g roup. 
Are all the p orts for that trunk c irc uit p ac k memb ers of that trunk? 
nIf yes, ad d  the memb ers, p ress En te r and  rep eat step s 2-6 for the 
next trunk c irc uit p ac k.
nIf no, rep eat step  2 for all the p orts on the trunk c irc uit p ac k that are 
not ac c ounted  for in that trunk g roup. (For examp le, if trunk g roup  
98 has only 4 memb ers, whic h c orrespond  to p orts 1 - 4, return to 
step  2 and  typ e display port
   and  p ress 
En te r to 
d etermine the trunk g roup  for p ort 5.) Then follow step s 3 and  4 with 
the new trunk g roup  information.
NOTE:
For more information ab out ad ministering  trunks, refer to D EFI N I TY 
Enterprise Communic ations Server Release 7 Ad ministration and  
Feature Desc rip tion
.
7. Type save translation
 and press 
En te r.
Identify and add station information
1. On the Release 7r management terminal, typ e list configuration 
port-network 
  (numb er of the SREPN p ort network) and  p ress 
En t e r. Id entify the slot numbers of the line c irc uit p ac ks.
2. For eac h line c irc uit p ac k on the Release 7r management terminal, typ e 
display port
   (where CCSS01 is the c irc uit p ac k and  p ort 
loc ation of the first port on the line c irc uit p ac k) and  p ress 
En t e r. The Port 
Information sc reen ap pears. The Identification:
 field shows the typ e 
of station and its extension for that port.
3. Type display station
   (extension of the station) and  p ress 
En t e r.
NOTE:
The d isp lay c ommand  d ep end s on the ad ministration of that p ort - 
display station
 for stations, display data
 for d ata terminals, and  so 
forth. 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-21 Administer the Release 7r and SRP 
1
4. On the SRP manag ement terminal, typ e add station
  
(extension is the same station extension as ab ove) and  p ress 
En t e r. 
5. Dup lic ate all of the station information d isp layed  on the Release 7r 
manag ement terminal to the SRP manag ement terminal. 
NOTE:
Rememb er to ad d  any ad d itional system ad ministration that may b e 
need ed . For examp le, if the station has a c overag e path, you need  to 
ad minister the c overage p ath. Some of the ad ministration for the 
station may not work if the SREPN g oes into survive mod e (suc h as 
coverage paths, abbreviated dial lists, and bridged appearances).
6. Repeat steps 2 - 5 for every port on every line c irc uit pack in the SREPN.
NOTE:
For more information ab out ad ministering  stations, refer to DEFINITY 
Enterprise Communic ations Server Release 7 Ad ministration and  
Feature Desc rip tion.
7. Type save translation
 and press En te r.
Identify and add other circuit packs
For c irc uit p ac ks other than trunk and  line, follow the same guid elines.
1. Disp lay eac h p ort on the c irc uit p ac k and  the eq uip ment typ e d isp layed  
on the p ort information sc reen.
2. Disp lay the eq uip ment on the Release 7r manag ement teminal and  ad d  
the information to the SRP manag ement terminal.
3. Type save translation
 and press 
En te r.
Administering the system features
NOTE:
Customer options availab le to the SRP are the same as those availab le on 
the existing  Release 7r. These are ad ministered  b y the reg ional CSA.
Any d ifferenc es in features from the Release 7r to Release 7si are 
exp erienc ed  in the survivab le mod e. Refer to the Release 7r and  
Release 7si feature ad ministration d esc rip tions for further d etails.
System ad ministration need s to b e ad d ed  to the SREPN inc lud ing  d ialp lan, 
system features, system maintenanc e, system sec urity, feature-ac c ess-c od es, 
and  so forth. Administer in the same manner as listed ab ove.
1. Disp lay the information on the Release 7r manag ement terminal. For 
examp le, typ e display feature-access-codes
 and  p ress 
En te r. 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-22 Administer the Release 7r and SRP 
1
2. Ad d  the information to the SRP manag ement terminal. For examp le, typ e 
change feature-access-codes
 and press 
En te r.
3. Type save translation 
(optional) and press 
En te r.
Administering the maintenance parameters
Pag e 1 of the system-p arameters maintenanc e form c ontains 2 fields that must 
b e ad ministered  for the ab b reviated alarm rep ort. Fi g u re  1 - 9
 shows the sc reen 
with the First OSS Telephone Number:
 and Second OSS Telephone 
Number:
 field s that are ad ministered  with offsite notific ation numb ers. The 
Abbrev Alarm Report?
 field s assoc iated  with these numb ers must be set to 
avoid unnec essary notific ation c alls.
1. Set the two Abbreviated Alarm Report
 field s to y
 and  p ress 
En t e r.
Figure 1-9. Maintenance-related system parameters screen
Administering the sync source
NOTE:
Do not ad minister a trunk on the SREPN as the sync hronization sourc e for 
the Release 7r. If the system g oes into the survive mod e, the Release 7r 
loses its sync source.
change system-parameters maintenance                     Page   1 of   3   SPE A
                   MAINTENANCE-RELATED SYSTEM PARAMETERS
OPERATIONS SUPPORT PARAMETERS
            Product Identification: 1010101010
        First OSS Telephone Number: 9~p5380532         Abbrev Alarm Report? y
       Second OSS Telephone Number: 9~p5380533         Abbrev Alarm Report? y
  Alarm Origination to OSS Numbers: both            
        Cleared Alarm Notification? y                 Suspension Threshold: 5 
              Restart Notification? y
           Test Remote Access Port? y
        CPE Alarm Activation Level: none   
     Customer Access to INADS Port? y
       Repeat Dial Interval (mins): 7 
SCHEDULED MAINTENANCE
                  Start Time: 23 : 00                   Stop Time: 06 : 00
           Daily Maintenance: daily              Save Translation: daily    
 Control Channel Interchange: daily     System Clocks Interchange: daily    
             SPE Interchange: daily 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-23 Replace Release 7r circuit packs 
1
To administer the sync  sourc e for the SRP:
1. On the SRP manag ement terminal, typ e change synchronization
 and  
p ress 
En t e r.
2. Enter a DS1 trunk c irc uit p ac k on the SRP as the primary sync  sourc e.
3. Press 
En t e r. 
NOTE:
When the system is in the survive mod e, the sync hronization of the 
SRP c omes from the DS1 trunk c irc uit p ac k. When the system is in 
the normal mod e, the sync hronization of the SRP reverts b ac k to the 
tone c loc k and  c auses a sync  alarm in the alarm log s of the SRP.
4. When all ad ministration is c omp leted  on the SRP, typ e save translation
 
and  p ress 
En t e r.
5. Return the TN2301 switc h to the AUTO p osition.
Replace Release 7r circuit packs
If the Release 7r has the TN574 DS1CONV c irc uit p ac k:
1. Rep lac e the TN574 DS1CONV c irc uit p ac k with the TN1654 DS1CONV 
circuit pack.
2. If you have a TN573 SNI c irc uit p ac k, rep lac e it with a TN573B SNI c irc uit 
pack.
Replace EPN circuit packs 
and make cable connections
1 . Po w e r  d o w n  t h e  EPN .
2. If this is a p reviously installed  EPN, then remove the DS1CONV to EI c ab le.
3. Install the TN775C maintenanc e c irc uit p ac k.
4. Install the TN570C exp ansion interfac e c irc uit p ac k.
5. Rep lac e the TN574 c irc uit p ac k with the TN1654 DS1CONV c irc uit p ac k.
6.Dep end ing  on the c ustomer’s c onfig uration, refer to one of the following  
sec tions:
n‘‘Connec t DS1CONV c ab les for standard /hig h reliab ility’’
n‘‘Connec t DS1CONV c ab les for c ritic al reliab ility’’
n‘‘Connec t d irec t fib er c ab les for stand ard /hig h reliab ility’’
n‘‘Connec t d irec t fib er c ab les for c ritic al reliab ility’’ 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-24 Replace EPN circuit packs and make cable connections 
1
Connect DS1CONV cables for standard/high
reliability
1. Connec t the eq uip ment as shown in Fig ure 1-10.
2. Power up the EPN.
3. Go to the ‘‘
Test the SRP’’ sec tion.
Connect DS1CONV cables for critical
reliability
1. Connec t the eq uip ment as shown in Fig ure 1-11.
2. Power up the EPN.
3. Go to the ‘‘
Test the SRP’’ sec tion.
Connect direct fiber cables for 
standard/high reliability
1. Connec t the eq uip ment as shown in Fig ure 1-12.
2. Power up the EPN.
3. Go to the ‘‘
Test the SRP’’ sec tion.
Connect direct fiber cables for critical reliability
1. Connec t the eq uip ment as shown in Fig ure 1-13.
2. Power up the EPN.
3. Go to the ‘‘
Test the SRP’’ sec tion. 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-25 Replace EPN circuit packs and make cable connections 
1
Figure 1-10. EPN DS1CONV standard/high reliability cable connectionsFigure Notes
1. MCC c ab inet
2. EPN c arrier A
3. DS1 c ab le from Port Network Connec tivity 
(PNC) A link
4. DS1CONV 2-foot (60.96 c m) Y c ab le (Tie wrap 
the cab le to the c ab inet.)
5. 9823A transceiver
6. 9823A transceiver on the EI connec tor7. B25A 25-p air c ab le
8. Main Distribution Frame (MDF)
9. Fib er op tic  cab les
10. From the EPN A TX and RX 
connec tors on the rear of the SRP
11. From the PPN A TX and RX 
connec tors on the rear of the SRP
cydf1sds RPY 030998
2
4
R
XT
X
1
3
6
4
2
5
10
119
9
7
3
8 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-26 Replace EPN circuit packs and make cable connections 
1
Figure 1-11. EPN DS1CONV critical reliability cable connectionsFigure Notes
1. MCC c ab inet
2. EPN c arrier B
3. EPN c arrier A
4. DS1 c ab les from Port Network Connec tivity 
(PNC) A and  B links
5. DS1CONV 2-foot (60.96 c m) Y c ab le (Tie wrap 
the cab le to the c ab inet.)
6. 9823A transceiver
7. 9823A transceiver on the EI connec tor8. B25A 25-p air c ab le
9. Fib er op tic  cab les
10. From the EPN B TX and RX 
connec tors on the rear of the SRP
11. Main Distribution Frame (MDF)
12. From the EPN A TX and RX 
connec tors on the rear of the SRP
13. From the PPN A TX and RX 
connec tors on the rear of the SRP
14. From the PPN B TX and RX 
connec tors on the rear of the SRP
2
45
RX
T
X
cydfhdsa RPY 030698
1
10
12
13
14
4
5
6
7
7
8
9
9
74
5
RX
T
X
6
2
3
9
9
11 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-27 Replace EPN circuit packs and make cable connections 
1
Figure 1-12. EPN Direct fiber standard/high reliability cable connectionsFigure Notes
1. SCC cab inet
2. 9823A transceiver on the EI connec tor
3. B25A 25-p air cab le
4. Main Distrib ution Frame (MDF)5. Fib er op tic  cab le
6. From the EPN A TX and RX 
connec tors on the rear of the SRP 
cabinet
cydf1epn RPY 030998
1
2
4
6
3
5 
						

							DEFINITY® Enterprise Communications Server Release 7 Installation and 
Maintenance for Survivable Remote EPN  555-233-102  Issue 2
June 1999
SREPN Installation 
1-28 Replace EPN circuit packs and make cable connections 
1
Figure 1-13. EPN Direct fiber critical reliability cable connectionsFigure Notes
1. MCC c ab inet
2. EPN c arrier B
3. EPN c arrier A
4. 9823A transceiver on the EI connec tor
5. Fib er op tic  cab les6. From the EPN B TX and RX 
connec tors on the rear of the SRP
7. Main Distribution Frame (MDF)
8. B25A 25-p air c ab le
9. From the EPN A TX and RX 
connec tors on the rear of the SRP
cydfhep2 RPY 030998
1
2
3
4
4
95
567
8