Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Administration For Network Connectivity Manual

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 
131
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
> Submit the screen
End
Destination 
NodeName of the far-end node for this channel. This must be a name 
entered on the Node Names screen. For ppp connections, it must 
match the Destination Node Name entered on the ppp Data 
Module screen.
Destination 
PortA value of 0 allows any available interface channel on the 
destination node to be used for this connection. The Interface 
Channel number for this connection on the Switch-2 Processor 
Channel screen must also be set to 0.
Session - 
LocalFor each connection, the Local Session number on this switch 
must equal the Remote Session number on the remote switch and 
vice versa. Session - 
Remote
Mach ID Leave blank for gateway applications. Field Conditions/Comments
3 of 3 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
132
Switch 1 Task — Assign Signaling Group and administered NCA TSC
This task assigns a signaling group and an administered NCA TSC for the ISDN 
connection to Switch 2.
Begin
Steps>
> Open the Signaling Groups form — enter ch sig n
> Enter values
> Press the Next Page key
change signaling-group next
                                                      Page 1 of 5
                           SIGNALING GROUP
Group Number: 1
    
Associated Signaling? y            Max number of NCA TSC: 5_
                       Primary D-Channel: 01b0924       Max number of CA TSC: 23                        Trunk Group for NCA TSC: 12       Trunk Group for Channel Selection: 12__
          Supplementary Service Protocol: a__
Field Conditions/Comments
Associated Signaling? Specifies Facility-Associated Signaling (FAS) — the 
D-channel carries signaling only for the B-channels on 
the same DS1 interface. 
Primary D-Channel Specifies D-Channel signaling on port 24 of the DS1 
circuit pack located at 01b09.
Max number of NCA 
TSCMaximum number of simultaneous non-call-associated 
Temporary Signaling Connections. The TSCs carry 
signaling for features not associated with a specific 
call; for example, signals to turn on Leave Word 
Calling.
Max number of CA 
TSCMaximum number of simultaneous call-associated 
TSCs that can exist in the signaling group. Typically, 
this is the number of ISDN-PRI trunk group members 
controlled by this signaling group.
Trunk Group for NCA 
TSCThe ISDN-PRI trunk group number whose incoming 
call-handling table will be used to handle incoming 
NCA-TSCs through this signaling group. 
Trunk Group for 
Channel Selection
Supplementary 
Service Protocola indicates AT&T protocol; b indicates QSIG protocol. 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 
133
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
> Enter values
              Page 2 of 5
ADMINISTERED NCA TSC ASSIGNMENT 
Service/Feature: __________           As-needed Inactivity Time-out (min): __
 TSC   Local                                                   Mach.
Index   Ext.  Enabled Established   Dest. Digits    Appl.   ID
  1:   2951_
     y     permanent  1701___________  dcs____  2_
  2:   2952_     y     permanent   1702___________  gateway   __
  3:   _____     _     _________   _______________  _______   __
  :  
 
Field Conditions/Comments
TSC Index 1: (for DCS connection to Switch 2)
Local Ext. Extension number of the ISDN interface on the Switch-1DS1 
circuit pack.
Enabled
y enables the administered NCA-TSC.
Established Used to indicate the strategy for establishing this administered 
NCA-TSC.
permanent means that the administered NCA-TSC can be 
established by either the near end or the far end.
as-needed means the administered NCA-TSC will be established 
the first time the administered NCA-TSC is needed; it can be set 
up either by the near end or far end switch.
Dest. Digits Extension number of the ISDN interface on the Switch-2 DS1 
circuit pack.
Appl. 1 TSC #1 carries the DCS signaling between node 1 and node 2.
Mach ID 1 Destination is node 2.
TSC Index 2: (for connection to Switch 2 for gateway to Switch 3)
Local Ext. Extension number of the ISDN interface on the Switch-1 DS1 
circuit pack.
Enabled
y enables the administered NCA-TSC.
Established Used to indicate the strategy for establishing this administered 
NCA-TSC.
permanent means that the administered NCA-TSC can be 
established by either the near end or the far end.
as-needed means the administered NCA-TSC will be established 
the first time the administered NCA-TSC is needed; it can be set 
up either by the near end or far end switch.
1 of 2 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
134
> Submit the screen
End
Dest. Digits Extension number of the ISDN interface on the Switch-2 DS1 
circuit pack.
Appl. Specifies that TSC #2 will carry signaling that will be converted in 
Switch-1 to another protocol (TCP/IP), which will then be 
forwarded to Switch-3.
Mach ID Leave blank for gateway Field Conditions/Comments
2 of 2 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 
135
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Switch 1 Task — Assign ISDN-TSC Gateway
This task assigns the ISDN TSC gateway channels needed for ISDN signaling 
between node 1 and node2
Begin
Steps
> Open the ISDN TSC Gateway Channel Assignment form — enter  ch isdn tsc
> Enter values
> Submit the screen
End
change isdn tsc-gateway                                         Page   1 of   2 
                      ISDN TSC GATEWAY CHANNEL ASSIGNMENT                       
   Sig   Admd NCA  Processor  Appli-     Sig   Admd NCA  Processor  Appli-
  Group  TSC Index   Channel   cation    Group  TSC Index   Channel   cation
 1: 1
_ 2_14_ dcs_ 17: __  __ ___ ____ 
 2: __ _____ ____ 18: __  __ ___ ____ 
 3: __  __ ___ ____ 19: __  __ ___ ____ 
 4: __  __ ___ ____ 20: __  __ ___ ____ 
 5: __  __ ___ ____ 21: __  __ ___ ____ 
 6: __  __ ___ ____ 22: __  __ ___ ____ 
:
Field Conditions/Comments
For Gateway Channel 1: (ISDN connection to Switch 2)
Sig Group Signaling group number assigned on the Signaling Group 
screen.
Adm’d NCA 
TSC IndexTSC Index assigned on page 2 of the Signaling Group screen 
(Administered NCA TSC Assignment).
Processor 
ChannelThis is the Processor Channel number specified as a gateway 
application on the Processor Channel Assignment screen.
Application The application that this TSC is used for. 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
136
Switch 2 Task — Assign Signaling Group and administered NCA TSC
This task assigns a signaling group and an administered NCA TSC for the ISDN 
connection to Switch 1.
Begin
Steps
> Open the Signaling Groups form — enter ch sig n
> Enter values
change signaling-group next
                                                      Page 1 of 5
                           SIGNALING GROUP
Group Number: 1
    
Associated Signaling? y            Max number of NCA TSC: 5_
                       Primary D-Channel: 01a1024       Max number of CA TSC: 23                        Trunk Group for NCA TSC: 12       Trunk Group for Channel Selection: 21__
          Supplementary Service Protocol: a__
Field Conditions/Comments
Associated 
Signaling?Specifies Facility-Associated Signaling (FAS) — the 
D-channel carries signaling only for the B-channels on 
the same DS1 interface. 
Primary D-Channel Specifies D-Channel signaling on port 24 of the DS1 
circuit pack located at 1a10.
Max number of NCA 
TSCMaximum number of simultaneous non-call-associated 
Temporary Signaling Connections that can exist in the 
signaling group. This number includes all NCA-TSCs 
that are administered on this screen and those that 
tandem through the switch in-route to another switch in 
the network. The TSCs carry signaling for features not 
associated with a specific call; for example, signals to 
turn on Leave Word Calling.
Max number of CA 
TSCMaximum number of simultaneous call-associated TSCs 
that can exist in the signaling group. Typically, this is the 
number of ISDN-PRI trunk group members controlled by 
this signaling group. If the connection is using the public 
network (SDN), the total NCA + CA TSCs cannot 
exceed the number ordered.
Trunk Group for 
NCA TSCThe trunk group used by the NCA-TSCs. 
Trunk Group for 
Channel SelectionLeave blank — this field is currently not used.
Supplementary 
Service Protocola indicates AT&T protocol; b indicates QSIG protocol. 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 
137
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
> Press the Next Page key
> Enter values
              Page 2 of 5
ADMINISTERED NCA TSC ASSIGNMENT 
Service/Feature: __________           As-needed Inactivity Time-out (min): __
 TSC   Local                                                   Mach.
Index   Ext.  Enabled Established   Dest. Digits    Appl.   ID
  1:   1701_
     y     permanent  2951___________  dcs____  1_
  2:   1702_     y     permanent  2952___________  dcs____  3_
  3:   _____     _     _________   _______________  _______   __
  :  
Field Conditions/Comments
TSC Index 1: (for DC S connection to Switch 1)
Local Ext. Extension number of the ISDN interface for TSC #1 on the 
Switch-2 DS1 circuit pack.
Enabled
y enables the administered NCA-TSC.
Established Used to indicate the strategy for establishing this administered 
NCA-TSC.
permanent means that the administered NCA-TSC can be 
established by either the near end or the far end.
as-needed means the administered NCA-TSC will be 
established the first time the administered NCA-TSC is needed; 
it can be set up either by the near end or far end switch.
Dest. Digits Extension number of the ISDN interface for TSC #1 on the 
Switch-1 DS1 circuit pack.
Appl. TSC #1 carries DCS signaling between node 2 and node 1.
Mach ID Destination is node 1.
TSC Index 2: (for DCS connection to Switch 1)
Local Ext. Extension number of the ISDN interface for TSC #2 on the 
Switch-2 DS1 circuit pack.
Enabled
y enables the administered NCA-TSC.
Established Used to indicate the strategy for establishing this administered 
NCA-TSC.
permanent means that the administered NCA-TSC can be 
established by either the near end or the far end.
as-needed means the administered NCA-TSC will be 
established the first time the administered NCA-TSC is needed; 
it can be set up either by the near end or far end switch.
1 of 2 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
138
> Submit the screen
End
Dest. Digits Extension number of the ISDN interface for TSC #2on the 
Switch-1 DS1 circuit pack.
Appl. TSC #2 carries DCS signaling between Switch 2 and Switch 1. 
As specified on the Switch-1 NCA TSC Assignment screen, 
TSC #2 is administered as a gateway on Switch 1, where the 
ISDN signals are converted to TCP/IP.
Mach ID Destination is node 3. Field Conditions/Comments
2 of 2 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 
139
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
3  C-LAN Administration
Switch 3 Task — Enable Bus Bridge Connectivity
This task enables the bus bridge functionality on the C-LAN circuit pack to provide a 
path between the packet bus and the processor.
Note:Bus Bridge Connectivity is used on the csi model only. This task may 
have been complete when the C-LAN circuit pack was installed.
Begin
Steps
> Open the Maintenance-Related System Parameters form — enter  ch sys ma
> Go to page 2 and skip to the Packet Intf2? field near the bottom of the screen
> Enter values
> Submit the screen
End
change system-parameters maintenance                            Page   2 of   3
 
                   MAINTENANCE-RELATED SYSTEM PARAMETERS           
MINIMUM MAINTENANCE THRESHOLDS ( Before Notification )
        TTRs: 4        CPTRs: 1        Call Classifier Ports: 0  
        MMIs: 0          VCs: 0  
TERMINATING TRUNK TRANSMISSION TEST ( Extension )
   Test Type 100:          Test Type 102:          Test Type 105:     
ISDN MAINTENANCE
   ISDN-PRI Test Call Extension:         ISDN-BRI Service SPID:           
DS1 MAINTENANCE
   DS0 Loop-Around Test Call Extension:      
LOSS PLAN ( Leave Blank if no Extra Loss is Required )
   Minimum Number of Parties in a Conference Before Adding Extra Loss:  
SPE OPTIONAL BOARDS
                     Packet Intf1? y     Packet Intf2? y
         Bus Bridge: 01a09__
Inter-Board Link Timeslots  Pt0: 6 Pt1: 1 Pt2: 1
Field Conditions/Comments
Packet Intf2? Enables the bus bridge.
Bus Bridge: Location of the C-LAN circuit pack. If the system has two
C-LANs, only one is administered for bus bridge.
Inter-Board 
Link 
Timeslots: 
Pt0, Pt1, Pt2Specifies the bandwidth used on the 3 ports of the Inter-Board 
Link. The total number of timeslots assigned cannot exceed 11. 
Pt0 carries PPP traffic and can have 1–9 timeslots. Pt1 carries 
maintenance messages and can have 1–3 timeslots. Pt2 carries 
broadcast messages and can have 1–3 timeslots. 
						

							Configuration 4:  R8csi  R8si Gateway 
 R8csi 3  C-LAN Administration
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
140
Switch 3 Task — Assign Node Names
This task assigns node names and IP addresses to each node in the network. This 
screen is administered on Switch 3. A Node Names screen must be administered on 
each switch in the network.
The node names and IP addresses in any network should be assigned in a logical and 
consistent manner from the point of view of the whole network. These names and 
addresses should be assigned in the planning stages of the network and should be 
available from the customer system administrator or from a Lucent representative.
Note:Enter node names for Intuity AUDIX and MSA adjuncts on page 1. Enter 
node names for switches, routers, and CMS starting on page 2.
Begin
Steps
> Open Node Names form — enter  ch node-n
> Go to page 2.
> Enter values.
> Submit the screen
End
change node-names
                                                                    Page 2 of 6
                                 NODE NAMES
   Name              IP Address          Name                IP Address
default
_________ 0__.0__.0__.0__ _______________ ___.___.___.___
node-1  __  192.168.10_.101   _______________    ___.___.___.___
node-3___        192.168.10_.103   _______________    ___.___.___.___
________________  ___.___.___.___    _______________    ___.___.___.___
Field Conditions/Comments
Name Enter unique node names for the following 2 nodes:
•C-LAN PPP port on Switch 3
•C-LAN PPP port on Switch 1.
IP Address The unique IP addresses of the nodes named in the previous 
field.