Lucent Technologies Definity Audix System Release 4.0 Guide

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Carrier Configuration Worksheets 
A-5  
A
Worksheet A-3: Port Slot Locations for
the DEFINITY AUDIX System 
Assembly
In the worksheet b elow, spec ify the loc ations of the two (one for a CMC) 
c ontig uous slots into whic h the DEFINITY AUDIX system assemb ly is to b e 
installed . 
The two c ontig uous slots are ad ministered  with c od es or left b lank as listed in the 
following  tab le. The assig nments are d epend ent on the switc h type. The 
rig ht-hand  slot will c onnec t with the TN568 c irc uit p ac k.  D ate _________________________
Pre p ar ed  b y _________________________
C on tac t tel ep hon e nu mb er _________________________
Slot occupied by
DEFINITY AUDIX SystemDigital Port
Equipment Location1 
1. For System 75, the eq uip ment loc ation is a 5-c harac ter id entifier; the first
c harac ter id entifies the c arrier, the sec ond  and  third c harac ters id entify the
slot numb er, and  the fourth and  fifth c harac ters id entify the p ort numb er. For
example, a valid  loc ation for System 75 is B0701
: c arrier B, slot 07, and  port
01. For all other switc hes, an add itional 1 or 2 d ig its is p rep ended to the c arrier,
slot, and  port loc ation to id entify the c abinet. For examp le, the loc ation
02B0701
 sp ec ifies c ab inet 02, c arrier B, slot 07, port 01. first
sec ond
Switch Left-hand slot Right-hand slot
All switc h releases 7.1 or 
higherADX12D
ADX8DTN568
All switc h release lower 
than 7.1TN754
TN2181 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Carrier Configuration Worksheets 
A-6  
A 
						

							Switch Administration Worksheets 
B-1  
B
Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
B
Switch Administration Worksheets
Before a software associate or software specialist can p erform initial switch 
ad ministration, he or she must ob tain c ertain information from the c ustomer. This 
ap p end ix has worksheets that a software assoc iate or software spec ialist and  the 
c ustomer should  c omp lete before installation. The worksheets inc lud e 
information nec essary for required  switc h ad ministration and  any op tional switc h 
features the c ustomer wants to use. These tasks are d esc rib ed  in d etail in 
Installation and  Switc h Ad ministration for the DEFINITY AUDIX System Release 
4.0, 
585-300-122.
Worksheets are inc lud ed  for the following  tasks:
nAd minister the voic e p orts as stations
nAssig n the hunt g roup
nAssign the call coverage group for voice ports
nAssig n the c all c overag e p ath for sub sc rib ers 
nAdminister digital networking ports 
nAd minister 7400A d ata mod ule or ADU
nAssign a hunt group for the digital networking ports
nAd minister a mod em
nAssign the hunt group for data modules, ADUs, and modems
In this ap p end ix, the following  c onventions ap p ly for values listed  in the 
rig ht-hand  c olumn of the worksheets:
n[ values in p lain typ e and  b rac kets]  are the d efaults
n[values in bold type with brackets]
 are rec ommend ed
nvalues in bold type with no brackets 
are req uired 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-2  
B
Worksheet B-1: Administer the Voice 
Ports as Stations 
The information in the following tables is required for administering the DEFINITY 
AUDIX voic e p orts on the switc h. For more information on these field s, see 
Installation and  Switc h Ad ministration for the DEFINITY AUDIX System Release 
4.0, 
585-300-122.
NOTE:
All d ig ital p orts must b e ad ministered on the switc h and  on the DEFINITY 
AUDIX system regardless of how many ports the customer purchased. 
However, only the numb er of ports ac tually p urc hased  are ad ministered  in 
the hunt g roup . D ate _________________________
Pre p ar ed  b y _________________________
C on tac t tel ep hon e nu mb er _________________________
Extension 
Comp lete next tab le. See next table
Set typ e options, d igital p ort emulationADX16D (
All switc h 
releases 7.1 and hig her)
1 
7405D 
(All switc h releases 
lower than 7.1;)
Po r tSee next table
Comp lete next tab le.
Name See next table
Comp lete next tab le.
Loc k Messag esn
Coverage Path
Enter the number you want to use to id entify the c overag e path for voic e ports. 
This c overag e p ath should c over all c alls to the DEFINITY AUDIX hunt g roup .
COR
To p revent toll fraud , Luc ent Tec hnolog ies rec ommend s that you selec t a Class 
of Restric tion (COR) for voic e ports suc h that sub sc rib ers c an only c all other 
numb ers with the 
same COR. If, after c areful c onsideration, you find  that 
sub sc rib ers d o need  to be ab le to c all numb ers with d ifferent CORs, add  
permissions for these (one at a time) as req uired . (The Digital Networking , 
Messag e Delivery, and  Outc alling  features req uire that sub sc rib ers b e ab le to 
ac c ess outsid e lines.) See 
DEFINITY AUDIX System — Ad ministration, 
585-300-507 for more information on p reventing  toll fraud .
COS
Selec t a c lass of servic e (COS) for the voic e p orts that p ermits the Call 
Forward ing  all Calls and  the Data Privac y features to b e ac tivated. Luc ent 
Tec hnolog ies rec ommends that the COS p ermit 
only these features to b e 
ac tivated .
LWC Rec eptionno 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-3  
B
LWC Ac tivationy
SMDR or CDR Privac y[n]
Red irec t Notific ation[n]
Brid g ed Call Alerting[n]
Coverage Messag e Retrieval[y]
Auto Answer[n]
Data Restric tion[n]
Id le Ap pearanc e Preferenc e[n]
Restric t Last Ap pearanc e
Comp lete next tab le. See next table
Coverage Mod ule[n]
AUDIX Name (G3r only)
This name app ears on the switc h USER-DEFINED ADJUNCT NAMES sc reen.
Disp lay Languag e (G3i-Glob al only)English
Feature Module (S75 and  G1 only)[n]
Head set (S75 only)[n]
Client Room Redirec tionYes
1. ADX16D is the recommend ed set typ e for d igital p ort emulation in all DEFINTY switc hes V2 and
hig her. 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-4  
B
Worksheet B-2: Assign the Hunt Group
The information in the following  tables is req uired  for assig ning  the hunt g roup. 
Use Tab le B-1 for switc h releases lower than G3V2 and  System 75. Use Tab le B-2 
for G3V2 and higher and Prologix.
Enter the loc ation, name, and  extension for eac h of the voic e p orts in the 
worksheets b elow. 
Enter the loc ation, name, and  extension for eac h of the 12 voic e p orts in the 
worksheet b elow:D ate _________________________
Pre p ar ed  B y _________________________
C on tac t Tel ep ho ne N u mb er _________________________
Table B-1. G3 Lower than V2, System 75
DEFINITY 
AUDIX PortDigital Port 
Equipment Location1
1. For System 75, the equip ment loc ation is a 5-c harac ter identifier; the first charac ter id entifies the
carrier, the second  and  third c haracters id entify the slot numb er, and the fourth and  fifth c haracters
id entify the port numb er. As an examp le, a valid loc ation for System 75 is 
B0701: c arrier B, slot 07,
and  p ort 01. For all other switc hes, an ad d itional 1 or 2 d ig its is prep end ed  to the c arrier, slot, and
p ort loc ation to id entify the c abinet. For examp le, the location 
02B0701 sp ec ifies c abinet 02, carrier
B, slot 07, port 01.
Name2
2. These names are recommend ed. Other names are ac c ep table, b ut they must b eg in with AUDIX
ExtensionRestrict Last
Appearance
1[AUDIX 1] n
2[AUDIX 2] n 
3[AUDIX 3] n
4[AUDIX 4] n
5[AUDIX 5] n
6[AUDIX 6] n
7[AUDIX TRANSFER] n
8[AUDIX 8] y 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-5  
B
The following  information is req uired  to d efine a hunt g roup (c ontaining  the voic e 
p ort members) for the DEFINITY AUDIX system voic e p orts. Only the number of 
p orts ac tually p urc hased  should  b e ad ministered  in the hunt g roup .
Table B-2.  G3V2 and Higher, ProLogix
DEFINITY 
AUDIX PortDigital Port 
Equipment Location Name ExtensionRestrict Last
Appearance
1[AUDIX 1] n
2[AUDIX 2] n
3[AUDIX 3] n
4[AUDIX 4] n
5[AUDIX 5] n
6[AUDIX 6] n
7[AUDIX 7] n
8[AUDIX 8] n
9[AUDIX 9] n
10[AUDIX 10] n
11[AUDIX TRANSFER] n
12[AUDIX 12] y
Group Number
Enter the number you want to id entify the DEFINITY AUDIX hunt group. (This numb er, 
prec ed ed b y an h
, is entered  in the voic e port COVERAGE PATH sc reen and  in 
sub sc rib er c overag e paths.)
Group Extension
Enter the extension numb er you want sub sc rib ers to d ial to retrieve their messag es from 
the DEFINITY AUDIX system. 
Group Type[ucd] (DEFINITY 
releases lower 
than 7)
ucd-mia 
(D EFI N ITY 
releases 7.1 and  
higher)
Group Name
Enter the name you want to ap p ear on d isp lay sets when sub sc rib ers c all the DEFINITY 
AUDIX system. (AUDIX must b e inc lud ed in the name for G3-MA to rec ognize this name 
as the DEFINITY AUDIX hunt group.)
Messag e Center[none]
ACD[n]
Queue (y/n)?[y] 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-6  
B
Vec tor (y/n)? (not available on System 75 and  G1)
The DEFINITY AUDIX hunt g roup  may b e vec tor c ontrolled  if Call Vec toring  is a feature on 
the switc h.[n]
COR
Enter the c lass of restric tion (COR) you want to assig n to the extension that sub sc ribers 
will c all to reac h the DEFINITY AUDIX system. For sec urity reasons, the DEFINITY AUDIX 
hunt g roup  should b e assigned its own COR that is restric ted  from ac c essing  all outg oing 
trunks or only those trunks need ed for Outc alling  or Dig ital Networking. 
The d efault COR 
is not rec ommend ed.
ISDN Call Disp
If ISDN-PRI is enab led, enter grp-name
 or mbr-name
 to spec ify whether the hunt g roup  
name or numb er is sent to the orig inating  subsc riber.
Queue Leng th
A sug g ested  length is the number of c onfigured DEFINITY AUDIX voic e ports.
First Announc ement Extension (not ap p lic ab le for G3r)
If you want a switc h rec ord ed announc ement, enter the extension numb er here.
First Announc ement Delay - in sec ond s (not ap plic ab le for G3r)
Optional if the q ueue is 
y and  must b e blank if there is no first announc ement. 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-7  
B
Worksheet B-3: Assign the Call 
Coverage Path for Voice Ports
The following information is req uired  to d efine c all c overag e p aths for the 
DEFINITY AUDIX voic e p orts.D ate _________________________
Pre p ar ed  B y _________________________
C on tac t Tel ep ho ne N u mb er _________________________
Coverage Path Numb er
Use the same c overag e p ath number as Worksheet B-1
.
Coverage Criteria
Station/Group  Status Ac tive? (Inside Call/Outside Call)[n/n]
Coverage Criteria
Busy? (Inside Call/Outside Call)[n/n]
Coverage Criteria
Dont Answer? (Inside Call/Outside Call)[n/n]
Coverage Criteria
All? (Insid e Call/Outside Call)[y/y]
SAC/Go to Cover? (Insid e Call/Outside Call)[n/n]
Next Path Numb er
If d esired , enter the sec ond  p ath to whic h c alls will be d irec ted  in c ase the c urrent 
p ath fails.
Numb er of Ring suse the default
Coverage Points
Po i n t 1
En t e r h
 followed  by the DEFINITY AUDIX hunt g roup  numb er from Worksheet B-2
. 
						

							Planning for the DEFINITY AUDIX System Release 4.0  585-300-602  Issue 1
May 1999
Switch Administration Worksheets 
B-8  
B
Worksheet B-4: Assign the Call 
Coverage Path for Subscribers
The following information is req uired  to d efine c all c overag e p aths for 
sub sc rib ers. Comp lete a c op y of this worksheet for eac h d ifferent c overag e p ath.D ate _________________________
Pre p ar ed  B y _________________________
C on tac t Tel ep ho ne N u mb er _________________________
Coverage Path Numb er
Enter the number you want to id entify the c all c overage p ath for sub sc rib ers.
Coverage Criteria
Station/Group  Status Ac tive? (Inside Call/Outside Call)[n/n]
Coverage Criteria
Busy? (Inside Call/Outside Call)[y/y]
Coverage Criteria
Dont Answer? (Inside Call/Outside Call)[y/y]
Coverage Criteria
All? (Insid e Call/Outside Call)[n/n]
SAC/Go to Cover? (Insid e Call/Outside Call)[y/y]
Next Path Numb er
If d esired , enter the sec ond  p ath to whic h c alls will be d irec ted  in c ase the c urrent path fails.
Numb er of ring s
Enter the numb er of ring s (1–99) you want before a c all g oes to c overag e. Three is rec ommend ed .
Coverage Points
For Point1, Point2, or Point3, enter h
 followed  b y the DEFINITY AUDIX hunt g roup  number.