Lexmark X544 Manual

Custom Scan Sizes menu
Menu itemDescription
ID Card
Width
1–14 inches (25–355.6 mm)
Height
1–14 inches (25–355.6 mm)
Orientation
Landscape
Portrait
2 scans per side
Off
OnSpecifies a non‑standard scan size.
Notes:
4.83 inches is the US factory default setting for Width. 123 millimeters is
the international factory default setting for Width.
6.32 inches is the US factory default setting for Height. 161 millimeters is
the international factory default setting for Height.
Landscape is the factory default...

Menu itemDescription
Portrait Width
3–14.7 inches
76–360 mmSets the portrait width
Notes:
If the width exceeds the maximum, the printer uses the maximum
width allowed.
8.5 inches is the US factory default setting. Inches can be increased
in 0.01‑inch increments.
216 mm is the international factory default setting. Millimeters can
be increased in 1‑mm increments.
Portrait Height
3–14.7 inches
76–360 mmSets the portrait height
Notes:
If the height exceeds the maximum, the printer uses the maximum
height...

Menu itemDescription
Fax ShortcutsPrints a report containing information about fax shortcuts
Profiles ListPrints a list of profiles stored in the printer
Print FontsPrints a report of all the fonts available for the printer language currently set in
the printer
Print DefectsPrints a repeating defects page used as a diagnostic tool for identifying print
problems
Note: Should be printed on letter‑ or A4‑size paper. If printed on smaller
paper, the content will be clipped.
Print DemoPrints a resident...

Menu itemDescription
PS SmartSwitch
On
OffSets the printer to automatically switch to PS emulation when a print job requires
it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PCL emulation if PCL
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PCL SmartSwitch is set to Off.
NPA Mode
Off
AutoSets the...

Wireless menu
Use the following menu items to view or configure the wireless internal print server settings.
Note: This menu is available only for network models or printers attached to print servers when an optional wireless
internal print server is installed in the printer.
Menu itemDescription
Mode
Infrastructure
Ad hocLets you select a mode
Notes:
Infrastructure mode makes the printer wireless network accessible
through an access point.
Ad hoc mode configures the printer for peer‑to‑peer wireless...

Menu itemDescription
NPA Mode
Off
AutoSets the printer to perform the special processing required for bidirectional
communication following the conventions defined by the NPA protocol
Notes:
Auto is the factory default setting.
Changing this setting from the printer control panel and then exiting the
menus causes the printer to restart. The menu selection is updated.
USB Buffer
Disabled
AutoSets the size of the USB input buffer
Notes:
Auto is the factory default setting.
Changing this setting from the...

Settings menu
General Settings menu
Menu itemDescription
Display Language
English
Francais
Deutsch
Italiano
Espanol
Dansk
Norsk
Nederlands
Svenska
Portuguese
Suomi
Russian
Polski
Magyar
Turkce
Cesky
Simplified Chinese
Traditional Chinese
Korean
JapaneseSets the language of the text appearing on the display
Note: All languages may not be available for all printers.
Eco‑Mode
Off
Energy
Energy/Paper
PaperMinimizes the use of energy, paper, or specialty media
Notes:
Off is the factory default setting. Off...

Menu itemDescription
Run Initial setup
Yes
NoInstructs the printer to run the setup wizard
Notes:
Yes is the factory default setting.
After completing the setup wizard by selecting Done at the
Country select screen, the default setting becomes No.
Paper Sizes
U.S.
MetricSpecifies the printer factory default measurements. The default
setting is determined by the country selection in the initial setup
wizard.
Scan to PC Port Range
Specifies a valid port range for printers behind a port blocking
firewall....

Menu itemDescription
Timeouts
Print Timeout
Disabled
1–255Sets the amount of time in seconds the printer waits to receive an
end‑of‑job message before canceling the remainder of the print job
Notes:
90 seconds is the factory default setting.
When the timer expires, any partially printed page still in the
printer is printed, and then the printer checks to see if any
new print jobs are waiting.
Print Timeout is available only when using PCL or PPDS
emulation. This setting has no effect on PostScript...

Menu itemDescription
Factory Defaults
Do Not Restore
Restore NowReturns the printer settings to the factory default settings
Notes:
Do Not Restore is the factory default setting. Do Not Restore
keeps the user‑defined settings.
Restore returns all printer settings to the factory default
settings except Network/Ports menu settings. All downloads
stored in RAM are deleted.
Copy Settings menu
Menu itemDescription
Content
Text
Text/Photo
PhotographSpecifies the type of content contained in the copy job...