Home > Lexmark > Printer > Lexmark Optra S 1250 Manual

Lexmark Optra S 1250 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Lexmark Optra S 1250 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 427
    							5Setting Up Your Printer
    Setting Up Your Printer
    Getting Started
    Unpacking the Printer
    1Select a well-ventilated area as the location to set up your
    printer.Make sure you have a sturdy, low table or the
    optional printer cabinet on which to set the printer.
    Allow at least 304.8 mm (12 in.) of clearance on all sides of
    the printer. Since you may want to install more printer
    options or the standard dual 500-sheet drawer for the Optra
    S 2455, leave 137.16 cm (4 ½ ft) clearance above the printer.
    137.16 cm
    (4
    ½ft)
    304.8 mm
    (12 in.)
    508 mm
    (20 in.)304.8 mm
    (12 in.)304.8 mm
    (12 in.) 
    						
    							Setting Up Your Printer6
    Setting Up Your Printer
    Getting Started
    2Remove all items from the box except the printer. Make
    sure you have the items shown.If any items are missing,
    contact the place where you bought the printer.
    Save the carton and packing material in case you need to
    repack the printer for service or storage.
    CAUTION:
    Leave the printer in the box until you are
    ready to install it. Then use the hand grips on
    the printer or ask someone to help you lift it.
    Make sure your fingers are not under the
    printerwhenyousetitdown.
    Diskettes
    (May be included
    with certain models.)CD
    Power Cord
    Printer
    Dual 500-sheet Drawer
    (Optra S 2455 only) 
    						
    							7Setting Up Your Printer
    Setting Up Your Printer
    Getting Started
    Determining What to Install Next
    Install the following based on the printer you purchased.
    If you have purchased optional 250-sheet drawers, 500-sheet
    drawers, a 2000-sheet drawer, or the duplex option, install them
    nowbeforetheprinterissetinplace.Seethetablein“Adding
    Options to the Printer” on page 253 for more information. See the
    illustrations on pages 2, 3, and 4 to determine the order to install
    options.
    If you have an Optra S 2455, install the dual 500-sheet drawer. See
    “Installing the Dual 500-Sheet Drawer” as follows.
    Installing the Dual 500-Sheet Drawer
    The dual 500-sheet drawer is standard on the Optra S 2455. It
    consists of two attached support units. Each support unit contains
    a 500-sheet input tray.
    1Remove the dual 500-sheet drawer from the packaging.
    Remove any packing tape.
    2Pull the trays out of the support units.
    3Remove all packing material and tape from the trays.
    Support
    Units
    500-sheet
    Input Trays 
    						
    							Setting Up Your Printer8
    Setting Up Your Printer
    Getting Started
    Note:Options compatible with the Optra S 1855 are labeled with
    a colored circle. If the option is not labeled with a colored
    circle, do not install it on an Optra S 1855. See the table on
    page 1 for the location of the label.
    Note:Decide on an installation location to set the dual 500-sheet
    drawer.The printer will be placed on top of it, so allow enough
    clearance space. The location must be sturdy and large
    enough to accommodate the dual 500-sheet drawer and the
    printer. See page 5 for information on clearance space.
    4Grasp the dual 500-sheet drawer on each side at opposite
    corners and move it to the table or printer cabinet you
    selected as the installation location. 
    						
    							9Setting Up Your Printer
    Setting Up Your Printer
    Getting Started
    5Locate the following parts on the top surface of the upper
    support unit: the tab, the round hole, and the four square
    holes.The bottom surface of the printer has matching holes
    or feet that accommodate the tab, round hole, and four
    square holes.
    Note:If you have purchasedoptional drawersor theduplex option,
    install them now before the printer is set in place.
    CAUTION:
    Make sure your fingers are not under the
    printer when you set it down. Use the hand
    gripsontheprinterorasksomeonetohelp
    you lift it.
    Tab
    Round HoleSquare Hole 
    						
    							Setting Up Your Printer10
    Setting Up Your Printer
    Getting Started
    6Lift and place the printer on top of the support unit. Be
    sure the edges of the printer and the support unit are
    aligned so all the parts fit.The right side of the printer is
    aligned with the option.
    Hand Grip
    Support Unit 
    						
    							11Setting Up Your Printer
    Setting Up Your Printer
    Getting Started
    Attaching the Decals
    Decals, showing the number one, are on your printer and the
    250-sheet input tray as shown. This pair of decals keeps the
    250-sheet input tray paired with the printer.
    If you purchased an Optra S 2455 or optional drawers, you
    received a sheet of decals.
    Peel the decals from the sheet and attach them to the recessed areas
    on the support unit and the matching tray as shown.
    By using the decals you can keep the paper trays paired with the
    matching supports units. Using the labels and setting the paper
    size window (see page 23) helps you remember what paper size
    you have loaded into each tray. This is valuable information to
    have before you start setting values on the operator panel that
    relate to paper source, size, and type. 
    						
    							Setting Up Your Printer12
    Setting Up Your Printer
    Getting Started
    Removing the Print Cartridge
    Packaging
    1Push the upper release latch to the right to release the
    upper front door.
    2Raise the upper front door.It remains in place. 
    						
    							13Setting Up Your Printer
    Setting Up Your Printer
    Getting Started
    3Grasp the print cartridge by the hand grip.
    4Pull the print cartridge up and out. 
    						
    							Setting Up Your Printer14
    Setting Up Your Printer
    Getting Started
    5Pull on each end of the plastic, V-shaped piece and then
    pull the packaging material straight out.Discard all
    packaging material: the V-shaped piece, the foam, and the
    paper connected to the foam. 
    						
    All Lexmark manuals Comments (0)

    Related Manuals for Lexmark Optra S 1250 Manual