Kyocera KM 1650 User Manual

							Printer Settings 
ADVANCED OPERATION GUIDE 2-13
4Press S or T to select On or Off 
and press [Enter]. If On is 
selected, Change # displays.
5Press S or T to select Change # 
and press [Enter].
6Press S or T to select the frame 
mode and press [Enter].
7Press [Reset]. The Printer Basic screen displays.
EtherTalk
Set this option to On if connecting to an Apple Macintosh computer.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
and press [Enter].
3Press S or T to select EtherTalk 
and press [Enter].
4Press S or T to select On and 
press [Enter].
5Press [Reset]. The Printer Basic screen displays.
Back
On
NetWare
Off
On
NetWare
Off
Change #
Back
Auto
NetWare Frame
802.3
Back
Parallel
In terf ac e
Network
Network Setting
NetWare
TCP/IP
EtherTalk
Back
On
EtherTalk
Off
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
2-14 ADVANCED OPERATION GUIDE
TCP/IP
Set this option to On if connecting to a Windows network via TCP/IP.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
and press [Enter].
3Press S or T to select TCP/IP 
and press [Enter].
4Press S or T to select On and 
press [Enter].
DHCP
Set this option to On if using DHCP (Dynamic Host Configuration Protocol).
1Display the TCP/IP screen, refer to TCP/IP, on page 2-14.
2Press S or T to select Change # 
and press [Enter].
3Press S or T to select DHCP and 
press [Enter].
4Press S or T to select On and 
press [Enter].
Back
Parallel
In terf ac e
Network
Back
NetWare
Network Setting
TCP/IP
Back
On
TCP/IP
Off
On
Off
TCP/IP
Change #
Back
DHCP
TCP/IP Setting
IP Address
Back
On
DHCP
Off
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
ADVANCED OPERATION GUIDE 2-15
IP Address Setting
Use the following procedure to register an IP Address to the machine. 
Check with your network administrator before performing this procedure.
If you use the following procedure to register the IP Address manually, 
ensure DHCP is Off and TCP/IP is On. 
NOTE: Any changes made to network settings become valid after you 
power the machine off and on again.
1Display the TCP/IP screen, refer to TCP/IP, on page 2-14.
2Press S or T to select Change # 
and press [Enter].
3Press S or T to select IP 
Address and press [Enter].
4Press S or T to select IP 
Address and press [Enter].
5Use the keypad to enter the 
address. Enter the first segment 
of the IP Address in the 
highlighted area and press [#].
6Enter the next segment and press 
[#].
Enter the remaining segments 
using the same procedure.
Press [Enter] when the entire address has been entered.
On
Off
TCP/IP
Change #
Back
DHCP
TCP/IP Setting
IP Address
Back
DHCP
TCP/IP Setting
IP Address
IP Address
00 ..00.
IP Address
10 0..00.
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
2-16 ADVANCED OPERATION GUIDE
Subnet Mask Setting
Continue from the previous Step 6 to register the Subnet Mask address.
NOTE: If you are not sure of the appropriate Subnet Mask address, 
contact your Network Administrator.
1Display the TCP/IP Setting screen.
2Press S or T to select Subnet 
Mask and press [Enter].
3Enter the Subnet Mask address 
using the same procedure used 
for the IP Address in steps 8 - 9 of 
IP Address Setting.
Press [Enter] when the entire address has been entered.
Default Gateway
Continue from the previous Step 3 to register the Default Gateway.
NOTE: If you are not sure of the appropriate Default Gateway address, 
contact your Network Administrator.
1Access the TCP/IP Setting screen.
2Press S or T to select Gateway 
and press [Enter].
3Enter the Gateway address using 
the same procedure used for the 
IP Address in steps 8 - 9 of IP 
Address Setting.
Press [Enter] when the entire address has been entered.
4When you have entered all the network settings, press [Reset].
The Printer Basic screen displays.
DHCP
IP Address
TCP/IP Setting
Subnet Mask
Subnet Mask
00 ..00.
IP Address
Subnet Mask
TCP/IP Setting
Gateway
Gateway
00 ..00.
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
ADVANCED OPERATION GUIDE 2-17
Network Status Page Printing
When printing the Status Page, you can also print the network status page 
in succession.
1Display the Interface screen, refer to Access the Interface Screen, on page 
2-11.
2Press S or T to select Network 
press [Enter].
3Press S or T to select Network 
Status Page and press [Enter].
4Press S or T to select On or Off 
and press [Enter]. 
5Press [Reset]. The Printer Basic screen displays.
Back
Parallel
In terf ac e
Network
Network Setting
TCP/IP
EtherTalk
Network Status Page
Back
On
Network Status Page Setting
Off
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
2-18 ADVANCED OPERATION GUIDE
Emulation
The following settings are available:
• Emulation Mode Selection
• KC-GL Pen Thickness
• KPDL Error Printing
• KPDL (AUTO) Alternative Emulation Selection
NOTE: You can set the emulation for each interface.
Emulation Mode Selection
Emulation modes that can be used with this machine: PCL6, KC-GL, 
KDPL, KDPL (AUTO), Line Printer, IBM Proprinter, Diablo 630, EPSON 
LQ-850 
If you set KC-GL, you can set the thickness of the pen and page size.
If you set KPDL (AUTO), switching between KPDL and an alternative 
emulation mode will be automatically performed according to the print 
data.
If you set KPDL or KPDL (AUTO), the details of any error that occurs during 
printing can be printed.
1Press [Printer].
2Press S or T to select MENU 
and press [Enter].
3Press S or T to select Emulation 
and press [Enter].
4Press S or T to select the 
interface and press [Enter].
5Press S or T to select the 
emulation mode and press 
[Enter].
GO
CANCEL
Read y
MENU
Print Status Page
Men u
In terf ac e
Emulation
Back
Parallel
In terf ac e
Network
Back
PCL 6
Emulation
KC-GL
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
ADVANCED OPERATION GUIDE 2-19If you have selected KC-GL, refer to KC-GL Pen Thickness, on page 2-19.
If you have selected KPDL or KPDL (AUTO), refer to KPDL Error Printing, 
on page 2-20.
If you have selected KPDL (AUTO), refer to KPDL (AUTO) Alternative 
Emulation Selection, on page 2-20.
KC-GL Pen Thickness
If you have selected KC-GL emulation, you can set the thicknesses of the 
eight pens and the page size. Continue the procedure from step 5 of 
Emulation Mode Selection to setup.
1Press S or T to select KC-GL 
Pen Adjust and press [Enter].
2Press S or T to select the pen 
required and press [Enter].
3Press < or > to select the 
thickness (number of dots) and 
press [Enter].
4Press S or T to select Back and press [Enter].
5Press S or T to select KC-GL 
Page Set and press [Enter].
6Press S or T to select the page 
size and press [Enter].
NOTE: SPSZ is the size specified with the PRESCRIBE SPSZ 
command. For details of the PRESCRIBE commands, refer to the 
PRESCRIBE Command Reference Manual.
7Press [Reset]. The Printer Basic screen displays.
Back
KC-GL Pen Adjust
KC-GL
KC-GL Page Set
Back
Pen (1)
KC-GL Pen Adjust
Pen (2)
(01
Pen Width
199)dot(s)
Back
KC-GL Pen Adjust
KC-GL
KC-GL Page Set
B1
KC-GL Page Set
B0
SPSZ
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
2-20 ADVANCED OPERATION GUIDE
KPDL Error Printing
The details of any error that occurs during printing in the KPDL emulation 
mode can be printed. Continue the procedure from step 5 of Emulation 
Mode Selection to set up.
1Press S or T to select Print 
KPDL Errs and press [Enter].
If On is selected, the details of any 
error will be printed.
2Press [Reset]. The Printer Basic screen displays.
KPDL (AUTO) Alternative Emulation Selection
If you set KPDL (AUTO), switching between KPDL and an alternative 
emulation mode will be automatically performed according to print data. 
Continue the procedure from step 5 of emulation mode selection to setup.
Available emulation modes: PCL6, KC-GL, Line Printer, IBM Proprinter, 
DIABLO 630, EPSON LQ-850
1Press S or T to select Alt. 
Emulation and press [Enter].
2Press S or T to select the 
emulation mode and press 
[Enter].
3Press [Reset]. The Printer Basic screen displays.
Back
Print KPDL Errs
KPDL
Back
Alt. Emulatio n
KPDL(AUTO)
Print KPDL Errs
Back
PCL 6
Al t.  Emul atio n
KC-GL
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
ADVANCED OPERATION GUIDE 2-21
Font
You can select the default Font for the current interface. The default Font 
can be one of the internal fonts or a font stored in the optional Memory 
Card.
The following settings are available:
• Font Selection
•Font Size
• Courier/Letter Gothic Font Character Pitch
• Courier/Letter Gothic Thickness
• Code Set
• Printing a Font List
NOTE: You can set the font for each interface.
 Access the Font Screen
1Press [Printer].
2Press S or T to select MENU 
and press [Enter].
3Press S or T to select Font and 
press [Enter].
4Press S or T to select the 
interface to set and press [Enter].
The Font screen displays.
Select the options required.
GO
CANCEL
Read y
MENU
Men u
In terf ac e
Emulation
Fo nt
Back
Parallel
In terf ac e
Network
Downloaded From ManualsPrinter.com Manuals 
						

							Printer Settings 
2-22 ADVANCED OPERATION GUIDE
Font Selection
NOTE: If optional fonts as well as internal fonts are stored on the 
machine, a screen for selecting Internal font or Option font displays. Press 
S or T to select the font to set.
1Display the Font screen, refer to Access the Font Screen, on page 2-21.
2Press S or T to select Select 
Font and press [Enter].
3Press S or T to select the Font 
ID and press [Enter].
The font number displays.
Characters displayed before font 
numbers indicate the following items.
4Press < or > to select the font number and press [Enter]. For internal font 
numbers, refer to Printing a Font List, on page 2-25.
5Press [Reset]. The Printer Basic screen displays.
Back
Select Font
Fo nt
Co de Set
Back
Select Font
Detail
I000
Fo nt ID
I000
Display Description
IInternal font
SDownloaded fonts
MFonts in memory card
HFonts in RAM disk or optional hard disk
OFonts in optional ROM
Downloaded From ManualsPrinter.com Manuals