Kyocera FS 3040MFP User Manual

8
8-113
Default Setting (System Menu)
Adding a Destination on One-touch Key
This machine has 11 one-touch keys and you can register 2 destinations to each of them.
The one-touch keys are arranged as shown below:
NOTE: Refer to  One-Touch Key on page 3-3  for how to use them.
Registering new destination
Use the procedure below to register a new destination under a One-touch key.
1In the Send or FAX  screen, press the one-touch key to 
which you want to register the destination and hold it (2 
seconds or...

8-114
Default Setting (System Menu)
Editing One-touch Key
Edit/delete the destinations you added to One-touch Key.
Use the procedure below to edit the one-touch key.
1In the Send or FAX screen, press the one-touch key 
where you want to edit the destination and hold it (2 
seconds or longer). Select Key Set. appears.
The screen shown is the one when No.1/No.12 is 
pressed and held.
2Press the U or V key to select the key number where 
you want to edit the destination.
3Press the OK  key. The Key Edit...

8
8-115
Default Setting (System Menu)
8Press [Yes] (the Left Select key). The selected 
destination is registered  to the one-touch key, 
overwriting the previous one.  Registered. is displayed 
and the screen returns to the basic screen.
Downloaded From ManualsPrinter.com Manuals 

8-116
Default Setting (System Menu)
Restarting the System
Restart the printer without turning the main power switch off. 
Use this to deal with any unstable operation by the machine. 
(Same as the computer restart.) 
Use the procedure below to restart the system.
1In the Sys. Menu/Count. menu, press the  U or V  key to 
select [System], and press the  OK key.
A login screen will appear. Then , enter the user ID and 
password with administrator  privileges to log in, and 
press [Login] (the  Right Select...

8
8-117
Default Setting (System Menu)
Network Setup
The following network settings are available.
• LAN Interface Setup …8-117
• TCP/IP (IPv4) Setup …8-118
• TCP/IP (IPv6) Setup …8-127
• NetWare Setup …8-128
• AppleTalk Setup …8-129
• Protocol Detail …8-133
LAN Interface Setup
Specify the settings for the LAN interface to be used. The default setting is Auto.
Use the procedure below to select the interface.
1In the Sys. Menu/Count. menu, press the  U or V  key to 
select [System], and press the  OK key....

8-118
Default Setting (System Menu)
6Press the OK key. LAN Interface appears.
7Press the U or V key to select the desired LAN 
interface.
The available LAN interfaces are as follows:
Auto
10Base-Half
10Base-Full
100Base-Half
100Base-Full
8Press the OK  key. Completed.  is displayed and the 
screen returns to the Network Setting menu.
TCP/IP (IPv4) Setup
Set up TCP/IP to connect to the Windows network. Set  the IP addresses, subnet masks, and gateway addresses. 
The default settings are TCP/IP Protocol:...

8
8-119
Default Setting (System Menu)
3Press the U or V key to select [Network Setting].
4Press the OK  key. The Network Setting menu appears.
5Press the U or V key to select [TCP/IP Settings].
6Press the OK  key. The TCP/IP Settings menu appears.
7Press the U or V key to select [TCP/IP].
8Press the OK  key. TCP/IP appears.
9Press the U or V key to select [On] and then press the 
OK  key.
Completed.  is displayed and the screen returns to the 
TCP/IP Settings menu.
10Press the U  or V key to select [IPv4...

8-120
Default Setting (System Menu)
13Press the OK key. DHCP appears.
14Press the U or  V key to select [Off ] and then press the 
OK  key. 
Completed.  is displayed and the screen returns to the 
IPv4 Setting menu.
15Press the U  or V key to select [Bonjour].
16Press the OK  key. Bonjour appears.
17Press the U or  V key to select [Off ] and then press the 
OK  key. 
Completed.  is displayed and the screen returns to the 
IPv4 Setting menu.
18Press the U  or V key to select [IP Address].
19Press the OK...

8
8-121
Default Setting (System Menu)
Press the U or V key or the numeric keys to enter the 
IP Address. Each 3 digits can be set between 000 and 
255.
IMPORTANT:  When the DHCP Setting ( page 8-123) is [On], 
the current IP address is displayed and cannot be changed.
When setting an IP address, set the DHCP Setting ( page 8-
123) to Off.
21Press the OK  key. Completed.  is displayed and the 
screen returns to the IPv4 Setting menu.
22Press the U  or V key to select [Subnet Mask].
23Press the OK  key....

8-122
Default Setting (System Menu)
27Press the OK key. Default Gateway appears.
28Use the arrow keys to enter the Default Gateway.
Press the Y or  Z key to move the  cursor position 
horizontally.
Press the U  or V key or the numeric keys to enter the 
Default Gateway. Each 3 digits can be set between 000 
and 255.
IMPORTANT:  When the DHCP Setting ( page 8-123) is [On], 
the current Default Gateway is displayed and cannot be 
changed.
When setting an Default Gate way, set the DHCP Setting 
(page 8-123...