Konica Minolta magicolor 5670EN User Manual

Replacing Consumables 167 Replacing the Waste Toner Bottle
When the waste toner bottle becomes full, the message WASTE TONER 
FULL/REPLACE BOTTLE 
appears in the message window. The printer 
stops and will not start again until the waste toner bottle is replaced.
1Open the printer’s front cover.
2Turn the dial on the waste toner 
bottle counterclockwise until it is 
in the unlock position.
Lock Unlock
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 168
3Open the left and right handles 
of the waste toner bottle.
4Grab the left and right handles of 
the waste toner bottle, and then 
slowly pull out the bottle.
Be careful since some 
waste toner may spill if 
the lock is closed when 
the waste toner bottle is 
removed.
5Remove the new waste toner bottle from its packaging. Insert the used 
waste toner bottle into the plastic bag included in the box, and then box it 
up.
Note
Dispose of the used waste toner bottle according to...

Replacing Consumables 169
6Slide the waste toner bottle all 
the way into the printer.
7Turn the dial clockwise until the 
waste toner bottle is in the 
locked position. 
Lock Unlock
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 170
8Close the front cover.
If the waste toner bottle is 
not fully inserted or if the 
dial is not locked, the 
front cover cannot be 
closed.
Replacing the Transfer Roller
When the time to replace the transfer roller is reached, the message 
TRANS.ROLLER/END OF LIFE appears. Printing can continue even 
after this message appears; however, since the print quality is reduced, the 
transfer roller should be replaced immediately.
When replacing the transfer roller, also replace the...

Replacing Consumables 171
2While pushing the levers to the 
inside, move the roller presser 
toward you. 
3While continuing to press the 
levers, remove the transfer 
roller.
4Prepare a new transfer roller.
5While pressing the levers, insert 
the shaft of the transfer roller 
into the bearings.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 172
6Move the levers away from you 
until it snaps into place.
7Close the right side cover.
8Reset the counter in the MAINTENANCE MENU/SUPPLIES/
REPLACE/TRANS. ROLLER 
menu.
9Replace the ozone filter, follow the procedure from next page.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 173
Replacing the Ozone Filter
1Remove the ozone filter from the 
printer.
2Slide the new ozone filter into 
the printer until it snaps into the 
place.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 174
Replacing the Transfer Belt Unit
When the time to replace the transfer belt unit is reached, the message 
TRANS. BELT/END OF LIFE appears. Printing can continue even after 
this message appears; however, since the print quality is reduced, the trans-
fer belt unit should be replaced immediately.
1Open the printer’s front cover.
2Remove the print unit and waste 
toner bottle.
For details on removing 
the print unit or waste 
toner bottle, refer to 
“Replacing a Print Unit” 
on...

Replacing Consumables 175
3Using a coin, remove the four 
screws on the left side.
Be careful not to lose the 
screws.
4Remove the left-side cover.
5Pull the lever, and then open the 
right side cover.
Before opening the right 
side cover, fold up Tray 
1.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 176
6Open the right side cover, and 
then use a coin to loosen the 
screws securing the transfer belt 
unit.
Before opening the right 
side cover, fold up Tray 
1.
7On the left side, pull to the right 
the blue shutter lever for the 
transfer belt unit.
Do not remove the blue 
lever.
8From the side where the left side 
cover was removed, hold the 
arm, and then carefully pull out 
the transfer belt unit.
Downloaded From ManualsPrinter.com Manuals