Konica Minolta magicolor 5670EN User Manual

Duplexing 147
Duplexing
Select paper with high opacity for duplex (double-sided) printing. Opacity 
refers to how effectively paper blocks out what is written on the opposite side 
of the page. If the paper has low opacity (high translucency), then the printed 
data from one side of the page will show through to the other side. Check 
your application for margin information. For best results, print a small quantity 
to make sure the opacity is acceptable.
Duplex (double-sided) printing can be done...

Output Tray 148
In addition, if “N-up” has been set to “Booklet”, autoduplex printing is per-
formed.
The following Order settings are available when “Booklet” is selected.
1Load plain paper into the tray.
2From the printer driver, specify duplex (double-sided) printing (Layout tab 
in Windows).
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.
Output Tray
All printed media is output to the face-down output tray on top of the printer. 
This tray has a...

Finishing 149
Finishing
When the optional staple finisher is installed, job separation, offset and staple 
printing can be performed. For the installation procedure, refer to “Staple Fin-
isher” on page 268. Settings can be specified for job separation, offset and 
staple printing by selecting 
JOB SEPARATION or FINISHING in PAPER 
MENU
.
Use the following paper with job separation, offset and staple printing.
Paper is fed to the main output tray with job separation, offset and sta-
ple printing.
Job...

Finishing 150
Offset Printing
If offset printing is selected, the paper is fed out shifted as shown below.
When PAPER MENU/COLLATE is set to ON, the pages are fed out 
in sets as shown below.
Staple printing
Pages are stapled and fed out by job or by copy set as shown below.
Page in the portrait orientation are stapled in the upper-left corner.
The copies can be stapled when they contain 2 to 30 pages (3 to 60 
pages when double-sided).
If staple printing is selected when COLLATE is set to ON, the...

Media Storage 151
Media Storage
How do I store media?
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust.
„Avoid leaning media...

Media Storage 152
Downloaded From ManualsPrinter.com Manuals 

Replacing
Consumables
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 154
Replacing Consumables
Note
Failure to follow instructions as outlined in this manual could result in 
voiding your warranty.
Note
If an error message (TONER OUT, TRANS.BELT END OF LIFE, etc.) 
appears, print out the configuration page, and then check the status of the 
other consumables. For details on the error messages, refer to “Error 
Messages (Warning:)” on page 238. For details on printing the 
configuration page, refer to “Printing a Configuration Page” on page 198.
About...

Replacing Consumables 155
Note
Do not use refilled toner cartridges or unapproved toner cartridges. Any 
damage to the printer or quality problems caused by a refilled toner 
cartridge or an unapproved toner cartridge will void your warranty. No 
technical support is provided to recover from these problems.
When replacing a toner cartridge, refer to the following table. For optimum 
print quality and performance, use only approved KONICA MINOLTA toner 
cartridges for your specific printer type, as listed...

Replacing Consumables 156
For optimum print quality and performance, use only the corre-
sponded TYPE genuine KONICA MINOLTA toner cartridges.
Keep toner cartridges: 
„In their packaging until you’re ready to install them.
„In a cool, dry location away from sunlight (due to heat). 
The maximum storage temperature is 35°C (95°F) and the maximum 
storage humidity is 85% (noncondensing). If the toner cartridge is moved 
from a cold place to a warm, humid place, condensation may occur, 
degrading print...