Konica Minolta bizhub 601 User Manual

							751/6012-14
Using copy functions2
2.6 Selecting Finishing settings
Various settings can be selected for sorting and finishing copies fed into the 
output tray.
The following Finishing settings are available.
*1If no finisher is installed and all of the following conditions are met, printed 
copies can be fed out and sorted in an alternating crisscross pattern.
– 8-1/2 × 11 or 5-1/2 × 8-1/2-size (A4- or B5-size) paper is used.
– Paper of the same size and type is loaded with the w orientation in one 
paper tray and with the v orientation in another tray.
– The Auto Paper setting is selected.
– The Auto Paper setting is not selected when the Mixed Original 
setting is selected.
*2The Staple settings are available only if the optional finisher is installed.
*3The Punch settings are available only if the punch kit or Z folding unit is 
installed with the optional finisher.
*4The Half-Fold, Center Staple & Fold and Tri-Folding settings are available 
only if the optional Finisher FS-610 is installed.
SettingDescription
Collate (By Set) Select this setting to separate each set of a multi-page original.
Group Select this setting to separate the copies of each page in a multi-
page original.
Offset
*1Select this setting to feed out and sort printed copies in an 
alternating crisscross pattern if the sorting conditions are met 
when no finisher is installed.
Select this setting to feed out and stack the printed copies on top 
of each other with each set shifted to separate it when a finisher 
is installed.
Face Up The copies are output with their front sides facing up.
Staple
*2Select one of these settings to bind the printed copies with 
staples. Corner or 2 Position can be selected.
Punch
*3Select one of these settings to punch holes in the copies for filing 
them.
Half-Fold
*4Select this setting to fold copies in half before feeding them out.
Center Staple & Fold
*4Select this setting to staple copies at two places along the center 
before feeding them out.
Tri-Fold
*4Select this setting to fold copies in three before feeding them out.
Z-Fold
*5Select this setting to fold copies in half along the center, and 
additionally mountain-fold one of the halves before feeding them 
out.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-15
Using copy functions2
*5The Z-Fold setting is available only if the Z folding unit is installed with the 
optional finisher.
2
Note 
Certain finishing settings cannot be used together.
Follow the procedures described below to select Finishing settings.
2.6.1 Selecting the finishing method
1
In the Basic screen, touch [Finishing].
The Finishing screen appears.
2
Select the desired Finishing settings.
– To return to the main screen, touch [Main Screen].
3
Touch [OK].
The Basic screen appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-16
Using copy functions2
2.6.2 Selecting Staple/Punch settings
1
In the Basic screen, touch [Finishing].
2
Touch [Staple/Punch].
– To return to the main screen, touch [Main Screen].
The Staple/Punch screen appears.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-17
Using copy functions2
3
Touch the button for the desired settings, and then touch [Position 
Setting].
4
Select the desired position.
– Touch [Auto] to automatically determine the stapling or hole-punching 
position according to the orientation of the loaded original. The paper is 
stapled or holes are punched along the long side of the paper if the 
original length is 11-11/16 inch (297 mm) or less or along the short side 
of the paper if the original length is more than 11-11/16 inch (297 mm).
When the 2 Position Staple setting is selected
5
Touch [OK], and then touch [OK] in the next two screens that appear. 
Otherwise, touch [Main Screen].
The Basic screen appears again.
2
Note 
The number of punched holes differs depending on the country (region) where the 
unit is installed. For details, consult your service representative.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-18
Using copy functions2
2.6.3 Selecting a folding or binding setting
1
In the Basic screen, touch [Finishing].
2
Touch [Fold/Bind].
– To return to the main screen, touch [Main Screen].
The Fold/Bind screen appears.
3
Select the desired settings.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-19
Using copy functions2
– To cancel the setting, touch [No].
4
Touch [OK], and then touch [OK] in the next screen that appears. 
Otherwise, touch [Main Screen].
The Basic screen appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-20
Using copy functions2
2.7 Selecting not to rotate the image
Copies can be printed with the image not rotated to fit the orientation of the 
loaded paper.
2
Note 
Depending on the paper size and zoom ratio, some parts of the image may be 
lost.
Follow the procedure described below to select the setting to not rotate the 
image.
1
Touch [Auto Rotate OFF].
– To cancel the setting for not rotating the image, touch [Auto Rotate OFF] 
again.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-21
Using copy functions2
2.8 Selecting the quality of the original
Select an original quality setting. Select the setting for the original type to 
better adjust the copy quality.
The following Original Type settings are available.
Follow the procedure described below to select an Original Type setting.
1
Position the original to be copied.
– For details on positioning the original, refer to Feeding the original on 
page 1-11.
2
Touch the Original Settings tab.
The Original Settings screen appears.
SettingDescription
Text Select this setting when copying originals containing only text.
Dot Matrix Original Select this setting when copying originals containing only text 
that appears faint (such as that written with a pencil).
Text/Photo Select this setting when copying originals containing both text 
and photos.
Photo Select this setting when copying originals containing only photos 
(halftones).
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-22
Using copy functions2
3
Touch [Original Type].
The Original Type screen appears.
4
Touch the button for the quality setting most appropriate for the 
loaded original.
– To return to the main screen, touch [Main Screen].
5
Touch [OK].
The Original Settings screen appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							751/6012-23
Using copy functions2
2.9 Selecting the density settings
Specify the copy density and background density. Adjust to the best density 
according to the status of the originals.
The following density adjustments are available.
Follow the procedures described below to select the density settings.
2.9.1 Adjusting the print density (Density settings)
1
Touch [Density/Background] on the Basic screen.
The Density/Background screen appears.
2
Touch [Density].
The Density screen appears.
ParameterDescription
Density The print image density can be adjusted to one of nine levels.
Background Removal The density of the background color of the original can be 
adjusted to one of nine levels.
Downloaded From ManualsPrinter.com Manuals