Konica Minolta bizhub 420 User Manual

Combine Originals/ Original Image Type5
bizhub 500/420/360 (Phase 3) 5-25
Copy Conditions 
Incompatible 
with Combine 
Originals/
Original Image 
Type SettingsApplication
Book CopyBooklet Pagination
Image 
Repeat
Page MarginEdit Margin
EraseImage 
Adjustment
Booklet
Stamp
Set RangeAuto Original Size DetectRepeatErase/Center EraseNon-Image Area EraseCenteringNo RotationOriginal Size SettingCustom Size OriginalsSet NumberingPage #Date/TimeBuilt In StampWatermark Combine Originals
Combine Pages2in1+++++...

5Combine Originals/ Original Image Type
5-26 bizhub 500/420/360 (Phase 3),: Condition last selected has priority and the former selection will be 
released.
+: Condition previously selected has priority and warning message will be 
displayed.
*4: Condition last selected has priority when recommended zoom ratio is 
used in Combine Originals or Booklet.
*8: Incompatible when Booklet is automatically selected with Half Fold or 
Fold & Staple in combination.
Copy Conditions 
Incompatible 
with Combine...

6Application Functions
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals 

Application Functions6
bizhub 500/420/360 (Phase 3) 6-3
6 Application Functions
6.1 Copying onto OHP Transparencies (OHP Interleave)
Use this function to copy onto overhead projector transparencies.
In order to prevent the copied transparencies from sticking together due to 
the heat inside the machine, an interleaf can be inserted between the 
transparencies. The interleaf can be kept blank, or copied from the same 
original as transparency.
Function overview
The following functions are provided in OHP...

6Application Functions
6-4 bizhub 500/420/360 (Phase 3)0Load OHP transparencies in the bypass tray, one sheet at a time.
0Never load OHP transparencies in any tray other than bypass tray, 
otherwise machine trouble may be caused.
0Specify the paper type as OHP in paper setting for bypass tray.
0Load copy paper in any tray other than bypass tray to match the size of 
OHP transparencies. Paper of different sizes cannot be used as interleaf.
0With OHP Interleave specified, Auto Zoom and Sort are...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-5
3Specify the paper type as OHP.
– Touch the bypass tray key on the Paper Screen, then touch 
[Change Tray Settings].
Touch [OHP] to highlight it, then touch [OK].
The Paper Screen will be restored.
4Load copy paper in any tray other than bypass tray to match the size 
of OHP transparencies.
Downloaded From ManualsPrinter.com Manuals 

6Application Functions
6-6 bizhub 500/420/360 (Phase 3)
5Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
6Touch [Sheet/Cover/Chapter Insert], then touch [OHP Interleave].
The OHP Interleave Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 

Application Functions6
bizhub 500/420/360 (Phase 3) 6-7
7Specify the tray loaded with paper for interleaf.
– Touch to highlight the tray key loaded with paper for interleaf in 
step 3.
8Select [Copy] or [Blank].
– To copy the original image also onto interleaves, touch [Copy] 
under Copy or Blank to highlight it.
– To leave the interleaves blank, touch [Blank] under Copy or Blank 
to highlight it.
9Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the OHP Interleave Screen to cancel the...

6Application Functions
6-8 bizhub 500/420/360 (Phase 3)
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals