Konica Minolta bizhub 420 User Manual

Application Functions6
bizhub 500/420/360 (Phase 3) 6-49
2
Reminder 
Non-Image Area Erase function may not operate properly for dark 
original. In this case, check this function using the original with white 
background.
This function may also perform incorrectly if the lighting in the work place 
is directly over the original glass. In this case, consult your service 
representative about an appropriate place for installation.
2
Note 
To release the selected application function, touch [OFF].
To release...

6Application Functions
6-50 bizhub 500/420/360 (Phase 3)
6.8 Repeating Original Image on One Sheet (Image 
Repeat)
Use this function to print the original image repeatedly on a single sheet of 
paper.
The following two modes are provided for Image Repeat.
-Auto Repeat
Use the original glass to scan the original.
The machine automatically determines the number of repeats from 
detected original image size and paper size.
The original image size can be both detected automatically (Auto Detect) 
or...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-51Function overview
FunctionModeDescription
Auto Repeat Auto Detect + With 
Margin
Auto Detect + Without 
Margin
Set Range + With 
Margin
Set Range + Without 
Margin
2/4/8 Repeat 2 Repeat
4 Repeat
8 Repeat
Downloaded From ManualsPrinter.com Manuals 

6Application Functions
6-52 bizhub 500/420/360 (Phase 3)Setting Repeat Times Automatically
Select the Auto Detect or Set Range mode to automatically detect or 
manually specify the original image size, then let the machine determine the 
number of repeats from specified mode and magnification ratio.
0Scan the original from original glass. The ADF cannot be used to scan the 
original.
0Auto Detect mode uses Non-Image Area Erase function to automatically 
detect the original size. Keep the ADF open.
0Set...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-53
4Specify the paper tray on the Paper Screen.
– Touch [Paper] on the Basic Screen to display the Paper Screen.
– Touch the desired tray key to highlight it. Without this tray selection, 
the machine will automatically use copy paper loaded in tray 1 to 
print.
5Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 

6Application Functions
6-54 bizhub 500/420/360 (Phase 3)
6Touch [Book Copy/Repeat], then touch [Image Repeat].
The Image Repeat Screen will be displayed.
7Specify the desired Layout mode.
– Touch [With Margin] or [Without Margin] to highlight it.
Downloaded From ManualsPrinter.com Manuals 

Application Functions6
bizhub 500/420/360 (Phase 3) 6-55
8Specify the desired Scan Range mode.
– To detect the original size automatically, touch [Auto Detect].
Non-Image Area Erase will also be selected automatically.
– To specify the scanning area, touch [Set Range] to display the 
Standard Size Screen, then select the desired scanning area.
Use up/down arrow key to scroll to the desired size, if necessary.
Downloaded From ManualsPrinter.com Manuals 

6Application Functions
6-56 bizhub 500/420/360 (Phase 3)– To enter the dimensions of scanning area, touch [Custom Size] on 
the Standard Size Screen to display the Custom Size Screen, then 
enter the desired dimensions from the control panel keypad. In 
order to specify a fraction, touch the bidirectional arrow key to 
move the cursor, then use [+] and [–] to enter the desired value in 
0.1 mm increments.
– When [Set Range] is selected, close the ADF.
?Do you want to delete the dimensions once entered?...

Application Functions6
bizhub 500/420/360 (Phase 3) 6-57
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From...

6Application Functions
6-58 bizhub 500/420/360 (Phase 3)Specifying Repeat Times (2/4/8 Repeat)
Use this function to specify the number of repeats from 2, 4, and 8 times, 
irrespective of the original image size.
0Position the original on the original glass or in the ADF.
0Use Set Range mode to repeat a part of the original, not the entire image, 
by specifying the scanning area.
Select the standard size or enter the dimensions of custom size.
Available dimensions: 30.0 ~ 432.0 mm for side X, 30.0 ~ 297.0...