Konica Minolta bizhub 362 User Manual

2Before making copies
2-22 362/282/222
Before making copies
Chapter 2
2.3 Turning on the main power and the auxiliary power
This machine has two power controls: the main power switch and the [Pow-
er] (auxiliary power) key.
To turn on the machine
The main power switch turns on/off all functions of the machine. Normally, 
the main power switch is turned on.
The [Power] (auxiliary power) key turns on/off machine operations, for exam-
ple, for copying, printing or scanning. When the [Power] (auxiliary...

Before making copies2
362/282/222 2-23
Before making copies
Chapter 2
!
Detail 
When the [Power] (auxiliary power) key is turned on, the indicator on the 
[Start] key lights up in orange, and a screen indicating that the machine 
is starting up appears.
After a few seconds, the message “Now warming up. Ready to scan.” ap-
pears on the touch panel, and the indicator on the [Start] key lights up in 
green, indicating that a job can now be queued.
The default settings are the settings that are selected...

2Before making copies
2-24 362/282/222
Before making copies
Chapter 2
To scan during warm-up
1Press the [Power] (auxiliary power) key.
The indicator on the [Start] key lights up in orange.
A screen appears, indicating that the machine is warming up.
?How is the machine turned on?
%For details on turning on the machine, refer to “To turn on the ma-
chine” on page 2-22.
2After the warm-up 
screen is displayed, the 
Basics screen appears. 
After the message “Now 
warming-up. Ready to 
scan.” is displayed,...

Before making copies2
362/282/222 2-25
Before making copies
Chapter 2
6Press the [Start] key.
The document is scanned, and the job is added to the list of queued 
jobs.
7Check that the document has finished being scanned, and then posi-
tion the next document.
8Specify new copy settings and the desired number of copies, and then 
press the [Start] key.
– After the machine has finished warming up, the jobs will automati-
cally be printed in the order that they were queued.
?How is the printing of a job...

2Before making copies
2-26 362/282/222
Before making copies
Chapter 2
To turn off the machine
1Press the [Power] (auxiliary power) key.
The touch panel goes off.
2Set the main power 
switch to [o].
2
Reminder 
When turning the machine off, then on again with the main power switch, 
wait about 10 seconds to turn the machine on after turning it off. The ma-
chine may not operate correctly if it is turned on immediately after being 
turned off.
Do not turn off the machine with the main power switch or the...

Before making copies2
362/282/222 2-27
Before making copies
Chapter 2
Automatically returning to the default settings (Automatic panel reset)
If the [Reset] key is not pressed and no operation is performed for a specified 
length of time, settings that have not been programmed, such as the number 
of copies, are cleared and return to their default settings.
This is the automatic panel reset operation.
As the factory default, the automatic panel reset operation is performed after 
1 minute.
!
Detail 
The...

2Before making copies
2-28 362/282/222
Before making copies
Chapter 2
Automatically conserving energy (Low Power mode)
If no operation is performed for a specified length of time, the touch panel go 
off, and the machine enters a mode where it conserves energy.
This is the Low Power mode.
The machine can receive jobs even while it is in Low Power mode.
As the factory default, the machine enters Low Power mode after 15 minutes.
To recover from Low Power mode
1Press any key in the control panel or touch...

Before making copies2
362/282/222 2-29
Before making copies
Chapter 2
2The machine can receive jobs while it is warming up.
– The touch panel comes on again and, after the machine has fin-
ished warming up, it is ready to begin printing (within 30 seconds at 
normal room temperature (73.4°F)).
!
Detail 
The length of time until the machine enters Sleep mode can be set from 
Utility mode. For details, refer to “Sleep Mode” on page 11-13.
Darkening the touch panel (LCD Back-Light Off)
If no operation is...

2Before making copies
2-30 362/282/222
Before making copies
Chapter 2
Controlling machine use with user authentication (machine authentica-
tion)
If machine authentication settings have been set by the administrator, this 
machine can only be used by users registered with machine authentication.
0When machine authentication settings have been specified, only users 
that enter user names and passwords registered with user authentication 
can use this machine.
0Contact the machine’s administrator for a...

Before making copies2
362/282/222 2-31
Before making copies
Chapter 2
3Touch [Password].
4Type in the password, 
and then touch [Enter].
5Touch [Login].
– If the user name or 
password was incor-
rectly entered, the in-
put screen appears 
again. Type in the 
correct user name 
and password, and 
then touch [Login]
– Instead of touching 
[Login], press the 
[Access] key to com-
plete the operation.
The User Authentication screen disappears, and the Basics screen ap-
pears.
6Make copies using the desired...