Konica Minolta bizhub 362 User Manual

3Basic copy operation
3-56 362/282/222
Basic copy operation
Chapter 3
When finisher is installed
To bind copies with staples
1In the Basics screen, 
touch [Finishing].
The Finishing screen ap-
pears.
2Touch either [Corner 
Staple] or [2 Staples].
–If “Corner Staple” is 
selected, the copies 
are bound together 
with a staple in the 
upper-left corner.
– If “2 Staples” is se-
lected, [Position Set-
ting] appears in the 
screen. To select the 
binding position, 
continue with step 3.
– If a staple setting...

Basic copy operation3
362/282/222 3-57
Basic copy operation
Chapter 3
3Touch [Position Setting], 
and then select the de-
sired position.
– Touch [Auto] to auto-
matically determine 
the binding position 
according to the ori-
entation of the load-
ed document.
4Touch [Enter].
The Finishing screen appears again.
Punching holes in copies (punch settings)
!
Detail 
If a punch setting is to be selected, select the orientation in which the 
document is positioned. If an Original Direction setting is not...

3Basic copy operation
3-58 362/282/222
Basic copy operation
Chapter 3
2Touch [Hole-Punch].
– To cancel the punch 
setting, touch [Hole- 
Punch] again to 
deselect it.
3Touch [Position Setting], 
and then select the de-
sired position.
– Touch [Auto] to auto-
matically determine 
the position of the 
punched holes ac-
cording to the orien-
tation of the loaded 
document.
4Touch [Enter].
The Finishing screen appears again.
Downloaded From ManualsPrinter.com Manuals 

Basic copy operation3
362/282/222 3-59
Basic copy operation
Chapter 3
Binding copies at the center
Copies can be fed out folded in half and stapled at two places along the cent-
er.
To bind copies at the center
0For details on specifying the “Booklet” function, refer to “Creating book-
let copies (“Booklet” function)” on page 8-22.
0The position of the fold and the center staples can be adjusted from the 
Utility mode. For details, refer to “Crease/Center Staple” on page 11-17.
1Select the “Booklet”...

3Basic copy operation
3-60 362/282/222
Basic copy operation
Chapter 3
3The Finishing screen ap-
pears.
Touch [2 Staples] and 
[Crease].
– To cancel center 
binding, touch [2 
Staples] and [Crease] 
again to deselect 
them.
4Touch [Enter].
The Basics screen appears again.
Downloaded From ManualsPrinter.com Manuals 

Basic copy operation3
362/282/222 3-61
Basic copy operation
Chapter 3
3.11 Scanning the next document during printing (reserv-
ing a copy job)
The settings for the next copy job can be specified and the document can be 
scanned while a copy operation is being performed so that it can be printed 
once the current copy operation is finished.
To reserve a copy job
0A copy job can be reserved only if optional hard disk is installed.
0Up to 5 copy jobs, including the current copy job, can be queued.
0A copy...

3Basic copy operation
3-62 362/282/222
Basic copy operation
Chapter 3
3Press the [Start] key.
4After the current copy job is finished, the next copy job begins.
Downloaded From ManualsPrinter.com Manuals 

Basic copy operation3
362/282/222 3-63
Basic copy operation
Chapter 3
3.12 Stopping/deleting a job
The following procedure describes how to stop scanning the document, stop 
the printing operation and delete the copy job.
To stop/delete a copy job
0If a document is being scanned for a job, pressing the [Stop] key stops 
scanning and printing.
1Press the [Stop] key 
while a document is be-
ing scanned or a job is 
being printed.
After the message 
“Copy cycle temporarily 
suspended.” appears, 
scanning...

3Basic copy operation
3-64 362/282/222
Basic copy operation
Chapter 3
Downloaded From ManualsPrinter.com Manuals 

4
Additional copy operations
Chapter 4
Additional copy 
operations
Downloaded From ManualsPrinter.com Manuals