Konica Minolta bizhub 362 User Manual

5Troubleshooting
5-6 362/282/222
Troubleshooting
Chapter 5
To clear a paper misfeed in the ADF
1Pull up the lever for the 
misfeed-clearing cov-
er, and then open the 
cover.
2Carefully pull out any 
misfed paper.
3Swing up the docu-
ment guide lever.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting5
362/282/222 5-7
Troubleshooting
Chapter 5
4Turn the dial to feed 
out any misfed docu-
ments.
5While supporting the 
document feed tray 
with your right hand, 
carefully pull out any 
misfed documents.
6Return the document guide lever to its original position, and then close 
the misfeed-clearing cover.
!
Detail 
For details on the positions of paper misfeeds, refer to “Paper misfeed in-
dications” on page 5-5.
Downloaded From ManualsPrinter.com Manuals 

5Troubleshooting
5-8 362/282/222
Troubleshooting
Chapter 5
To clear a paper misfeed in the fusing unit
1Pull up the right-side 
door release lever, and 
then open the right-
side door.
7 CAUTION 
The area around the fusing unit is extremely hot.
%Touching any part other than those indicated may result in 
burns. If you get burnt, immediately cool the skin under cold 
water, and then seek professional medical attention.
Fusing unit
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting5
362/282/222 5-9
Troubleshooting
Chapter 5
2Carefully pull out any 
misfed paper.
– Decreased copy 
quality may result if 
the surface of the 
image transfer roll-
er is touched. Be 
careful not to 
touch the surface 
of the image trans-
fer roller.
3Open the fusing unit 
guide.
Image
transfer
roller
Downloaded From ManualsPrinter.com Manuals 

5Troubleshooting
5-10 362/282/222
Troubleshooting
Chapter 5
4Carefully remove any 
misfed paper.
5Open the switching 
guide, and then care-
fully pull out any mis-
fed paper in the 
switchback unit.
6Carefully pull out any 
misfed paper in the 
fusing section.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting5
362/282/222 5-11
Troubleshooting
Chapter 5
7Carefully pull out any 
misfed paper around 
the image transfer roll-
er.
8Carefully remove any 
misfed paper.
9Close the right-side door.
!
Detail 
For details on the positions of paper misfeeds, refer to “Paper misfeed in-
dications” on page 5-5.
Downloaded From ManualsPrinter.com Manuals 

5Troubleshooting
5-12 362/282/222
Troubleshooting
Chapter 5
2
Reminder 
If the paper is misfed as described below, contact your technical repre-
sentative.
- The paper is wrapped around the roller in the fusing unit.
- The paper is folded or shredded by the roller in the fusing unit.
- The paper that was removed tore and partly remains in the fusing unit.
To clear a paper misfeed in the automatic duplex unit
1Open the automatic 
duplex unit door.
2Carefully pull out any misfed paper.
3Close the automatic...

Troubleshooting5
362/282/222 5-13
Troubleshooting
Chapter 5
To clear a paper misfeed in the bypass tray
1Remove all paper from 
the bypass tray.
2If misfed paper cannot 
be pulled out, pull the 
lever for the sliding 
plate of the bypass 
tray, and then pull the 
sliding plate toward 
you.
Downloaded From ManualsPrinter.com Manuals 

5Troubleshooting
5-14 362/282/222
Troubleshooting
Chapter 5
3Press down on the 
sliding plate with your 
left hand and carefully 
pull out any misfed pa-
per.
4Return the bypass tray to its original position.
!
Detail 
For details on the positions of paper misfeeds, refer to “Paper misfeed in-
dications” on page 5-5.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting5
362/282/222 5-15
Troubleshooting
Chapter 5
To clear a paper misfeed in the 1st or 2nd tray
1Open the bypass tray.
2Pull up the lower right-
side door release le-
ver, and then open the 
lower right-side door 
of the paper feed unit 
indicated in the touch 
panel message.
Downloaded From ManualsPrinter.com Manuals