Konica Minolta bizhub 362 User Manual

4Additional copy operations
4-12 362/282/222
Additional copy operations
Chapter 4
4Check the copy settings registered with the selected program number.
– The program whose copy settings are being checked in the Check 
Program screen can be recalled. Touch [Recall] to recall the regis-
tered copy settings and display the Basics screen again.
5Touch [Enter].
The Program screen appears again.
!
Detail 
There are three Check Program screens. Touch [Fwd] to display the next 
screen, or touch [Back] to display...

Additional copy operations4
362/282/222 4-13
Additional copy operations
Chapter 4
3Touch the program 
number button regis-
tered with the copy set-
tings to be deleted. 
A message appears, re-
questing confirmation to 
delete the copy pro-
gram.
4Touch [Yes], and then touch [Enter]. To stop deleting the copy pro-
gram, touch [No], and then touch [Enter].
The Program screen appears again.
Downloaded From ManualsPrinter.com Manuals 

4Additional copy operations
4-14 362/282/222
Additional copy operations
Chapter 4
4.5 Specifying control panel settings (Accessibility mode)
This section contains details on the procedures for specifying control panel 
settings and adjusting the touch panel.
To display the Accessibility Settings screen
1Press the [Accessibility] 
key.
The Accessibility Set-
tings screen appears.
2Touch the button for the Accessibility function whose setting is to be 
changed.
The screen for the selected function...

Additional copy operations4
362/282/222 4-15
Additional copy operations
Chapter 4
!
Detail 
To return to the Basics screen from the Accessibility Settings screen, 
press the [Accessibility] key or the [Reset] key, or touch [Enter], [Set] or 
[Reset].
If [Reset] in the Accessibility Settings screen is touched to return to the 
Basics screen, the settings specified in the Accessibility Settings screen 
are not applied, and the Basics screen is reset to its factory default set-
tings.
If [Set] or [Enter] in...

4Additional copy operations
4-16 362/282/222
Additional copy operations
Chapter 4
To set the “Key Speed Settings” function
It is possible to specify the length of time until the value begins to change af-
ter a touch panel button is held down and the length of time for the value to 
change to the next number.
0The factory default setting for “Time to Start” is 0.3 second, and the fac-
tory default setting for “Interval” is 0.1 second.
1Display the Accessibility Settings screen. (For details, refer to...

Additional copy operations4
362/282/222 4-17
Additional copy operations
Chapter 4
To set the “Extend Auto Reset” function
If no operation is performed for a specified length of time, an automatic panel 
reset operation is performed and all settings in the touch panel return to their 
default settings. It is possible to specify the length of time that a confirmation 
screen is displayed before the settings return to their defaults.
0For details on the automatic panel reset operation, refer to...

4Additional copy operations
4-18 362/282/222
Additional copy operations
Chapter 4
To set the “Notification Screen” function
It is possible to specify the length of time that the screen is displayed to con-
firm the reception number or job ID after copying is finished.
0The factory default setting is “3 sec.”.
1Display the Accessibility Settings screen. (For details, refer to 
page 4-14.)
2Touch [Notification Screen].
The Notification Screen screen appears.
3Select the setting for the 
desired length of...

Additional copy operations4
362/282/222 4-19
Additional copy operations
Chapter 4
To set the “Sound Setting” function
It is possible to specify the volumes of the tone that is sounded when a touch 
panel button is touched and of the alarm that is sounded when a malfunction 
occurs.
0The factory default setting is “Normal”.
1Display the Accessibility Settings screen. (For details, refer to 
page 4-14.)
2Touch [Sound Setting].
The Sound Setting screen appears.
3Touch [Normal] or 
[Loud].
4Touch [Enter]....

4Additional copy operations
4-20 362/282/222
Additional copy operations
Chapter 4
To set the “Key Sound Tones” function
It is possible to specify the tone of the sound produced when a touch panel 
button is touched and of the alarm that is sounded when a malfunction oc-
curs.
0The factory default setting is “High”.
1Display the Accessibility Settings screen. (For details, refer to 
page 4-14.)
2Touch [Key Sound Tones].
The Key Sound Tones screen appears.
3Touch [Low], [Normal] or 
[High].
4Touch...

Additional copy operations4
362/282/222 4-21
Additional copy operations
Chapter 4
4.6 Job List screens
Jobs
Specifying the desired copy settings, then pressing the [Start] key queues 
the copy operation in this machine. This queued operation is called a job. In 
the same way, operations for making scans and computer printouts are also 
queued as jobs.
-Jobs that are being performed and jobs that are queued can be checked 
or deleted from the Job List screens.
-Jobs are printed starting with the one at...