Konica Minolta bizhub 362 User Manual

3Basic copy operation
3-46 362/282/222
Basic copy operation
Chapter 3
3.9 Selecting a Combine Originals setting
Multiple document pages (mainly 2, 4 or 8 pages) can be combined and 
printed on a single page, reducing paper use.
2
Note 
The factory default settings are the recommended zoom ratios.
!
Detail 
When a combined copy setting is selected, the recommended zoom ratio 
is selected, and the document image is copied at a reduced size.
The recommended zoom ratios for each setting are listed below....

Basic copy operation3
362/282/222 3-47
Basic copy operation
Chapter 3
SettingOriginal/copy settings and description
2 in 1 (page 3-46) Single-Sided % Single-Sided
Two single-sided documents is copied onto one double-sided 
sheet.
Single-Sided % Double-Sided
Four single-sided documents are copied onto one double-sid-
ed sheet.
Double-Sided % Single-Sided
One double-sided document is copied onto one single-sided 
sheet.
Double-Sided % Double-Sided
Two double-sided documents are copied onto one double-...

3Basic copy operation
3-48 362/282/222
Basic copy operation
Chapter 3
4 in 1 (page 3-46) Single-Sided % Single-Sided
Four single-sided documents are copied onto one single-sid-
ed sheet.
Single-Sided % Double-Sided
Eight single-sided documents are copied onto one double-
sided sheet.
Double-Sided % Single-Sided
Two double-sided documents are copied onto one single-sid-
ed sheet.
Double-Sided % Double-Sided
Four double-sided documents are copied onto one double-
sided sheet.
SettingOriginal/copy settings...

Basic copy operation3
362/282/222 3-49
Basic copy operation
Chapter 3
Copying multiple document pages onto a single page (combined copy 
settings)
1In the Simplex/Duplex screen, select the appropriate settings under 
“Orig.” and “Copy” for the desired combined copy. (For details, refer to 
page 3-39.)
2In the Basics screen, 
touch [Combine Origi-
nals].
The Combine Originals 
screen appears.
3Select the desired com-
bined copy settings.
– To cancel the setting, 
touch the button 
again to deselect it....

3Basic copy operation
3-50 362/282/222
Basic copy operation
Chapter 3
3.10 Selecting finishing for copies
Various settings are available for sorting and finishing copies that are fed out.
2
Note 
The factory default setting is “Non-Sort”.
!
Detail 
If no finisher is installed and the following conditions are met, printed 
copies can be fed out and sorted/grouped in an alternating crisscross 
pattern (crisscross sorting and crisscross grouping).
- Letter or 5-1/2 × 8-1/2 paper is used.
- Paper of the same...

Basic copy operation3
362/282/222 3-51
Basic copy operation
Chapter 3
The following six finishing settings are available.
SettingDescription
Non-Sort Select this setting to copy without using a Finishing setting.
Sort Select this setting to separate each set of a multi-page document.
Shift Sorting
Each set of copies is fed out shifted 
to separate them.Crisscross Sorting
Each set of copies is fed out in an 
alternating crisscross pattern to 
separate them.
Group Select this setting to separate the copies...

3Basic copy operation
3-52 362/282/222
Basic copy operation
Chapter 3
Corner  Staple Select this setting to bind the copies with a staple in the upper-left corner.
2 Staples Select this setting to bind the copies with two staples.
Center Binding 
(“Crease” and “2 
Staples” settings)The copies are folded in half, then stapled at two places along the center.
Hole Punch Holes are punched in the copies for filing them.
SettingDescription
1
11
11
Downloaded From ManualsPrinter.com Manuals 

Basic copy operation3
362/282/222 3-53
Basic copy operation
Chapter 3
Required options for the finishing settings
* Crisscross sorting and crisscross grouping are not available if a finisher is installed.
The following procedures describe how to select Finishing settings.
Separating copies by sets (“Sort” setting)
0The factory default setting is “Non-Sort”.
0If “Sort” is selected while no finisher is installed, printed copies will be fed 
out and sorted in an alternating crisscross pattern if the...

3Basic copy operation
3-54 362/282/222
Basic copy operation
Chapter 3
1In the Basics screen, 
touch [Finishing].
The Finishing screen ap-
pears.
2Touch [Sort].
Separating copies by pages (“Group” setting)
0The factory default setting is “Non-Sort”.
0If “Group” is selected while no finisher is installed, printed copies will be 
fed out and grouped in an alternating crisscross pattern if the following 
conditions are met. 
- Letter or 5-1/2 × 8-1/2 paper is used.
- Paper of the same size and type is loaded...

Basic copy operation3
362/282/222 3-55
Basic copy operation
Chapter 3
1In the Basics screen, 
touch [Finishing].
The Finishing screen ap-
pears.
2Touch [Group].
Stapling copies (staple settings)
!
Detail 
In order for copies to be stapled, all of the following conditions must be 
met.
- The paper width must be between 7-1/4 inch and 11-3/4 inch
- The paper length must be between 5-1/2 inch and 17 inch
- If the “Mixed Original” setting is selected, all copies must be printed 
with paper of the same...