Inter-Tel Imx/Gmx 416/832 Installation Manual

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION % MAINTENANCE PROGRAMMING 
Issue 1, November 1994 
Actions setup Exit 
Primary Attendant Station: 
011 Termination Digits: p&z-l 
astern Flags 
Description 
Allow cross-tenant voice mail/computer traffic 
Audible message indication for SL sets 
Auto attendant - dial during recording 
- enable ringback tone 
E. MISCELLANE 
OUS SYSTEM-WIDE 
INFORMATION (MISC) 
10.57 
Select h4iscellaneous System-Wide Informa- 
tion from the System-Wide Features menu or enter...

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
l Audible Message Indication for SL Sets: If 
enabled, single-line sets will receive message wait- 
ing indications (six tones before dial tone) when a 
message is waiting. In the default state, this is M- 
abltxi. 
0 Auto Attendant -Dial During Recording: To al- 
low callers to dial extension numbers while the auto- 
mated attendant message is playing, enable this op 
tion by setting it to “yes.” In the...

INTER-TELPRACTICES 
IMx/GMX 416/832 INSTALLATION % MAINTENANCE PROGRAMMING 
Issue 1, November 1994 
0 
0 
l 
Music-On-Hold for IC Calls: This option deter- 
mines whether a user hears music on hold when 
placed on hold by another station or camps on to a 
resource In the default state, this is enabled. 
OEIYA DSS Immediate ‘Ihnsmit: Determine if 
DSS-equipped keysets will have immediate Off- 
Hook Voice Announce capability enabled. In the de- 
fault state, this is disabled. 
OHVA System-Wide: Determine...

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 lNS‘WLL.A~ON & MAINTENANCE 
Actions setup Exit 
Page Zones 
0 l Belays 
0 External Ports 
[--iz-) 
[ convert Ports J 
bigned Ports/Relays Available Ports/Relays 
F. PAGE ZONES (PAGE) 
10.62 To prepare for page zone programming, make a 
list of the keysets and/or the external paging network(s) 
that are included in up to 10 paging zones. Keysets and 
the external paging network(s) can be in more than one 
page zone. (Refer to the...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSIALLATION & MAINTENANCE PROGRAMMING 
Issue 1, November 1994 
10.66 KEYSETS: 
To assign the keysets that will be in 
the page zone, select the Keysets command button. A 
station list window appears as shown below. 
1002 01.03 -Station Undefined 
1003 01.04 -Station Undefined 
1004 01.05 ‘Station Undefined 
1010 02.03 ‘Station Undefined 
101102.04 -Station Undefined 
1012 02.05 -Station Undefined 
0 INCLUDE or EXCLUDE: To include a station in 
that page zone, locate...

PROGRAMMING Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
Available Devices 
Individual CO Trunk 
Individual CO Trunk 
Individual CO 
TN& 
Individual CO TNII~ 
(-x-j 
10.67 CONVERT PORTS: To convert CO trunk or 
SLI circuits to external paging ports, select the Convert 
Ports command button (shown in window on page 
5-70). The window shown above appears. 
. EXTERNAL PAGE PORTS/AVAILABLE DE- 
VICKS: To convert an available device to an exter- 
nal paging port,...

lNTER-TELPRAcTIcES 
IMI4GM.X 416/832 INSTALLATION & -ANCE PROGRAMMING 
Issue 1. November 1994 
Actions setup Exit 
Belays 
03- Unknown Relay 
Tenant Group 
1 Available Relay l)q~~ 
Power-Fail Rela 
G. RELAY PROGRAMMING @CLAY) 
10.69 
Matrix Card and Expansion Card relays can be 
designated for external paging, night switch (which is 
activated when the system or associated tenant group is 
placed in night mode), power-fail, or signal device re- 
lays. Relay 1 is preprogrammed as the power-failure 
signal...

PROGRAMMING INTER-TELPRACTICES 
Issue 1, November 1994 IMX/GMX 416/832 INST4L,LATION 8z MAINTENANCE 
Forwarding Paths 
005 
006 
007 
008 
009 
H. SYSTEM FORWARDING (SFWD) 
10.74 
When System Forwarding is selected from the 
System Wide Features menu (or the SFWD command is 
entered), the programming window shown above ap 
pears. It is used for assigning forwarding points to the 
system forwarding paths. Stations can then be pro- 
grammed to use the forwarding paths in the window 
shown on page 5-41. A...

INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE PROGRAMMING 
Issue 1, November 1994 
&tions atup Exit 
Number of Displayed Speed Dial Numbers: 
l2E-l 
Speed Dial Number Programming Station: 
Eiirl 
Number of Digits in Bin Number: 
0 3 
System Speed Dial Numbers 
Tenant  # Name 
Number 
“...:.:.:.:.:.:.:.:.:.~.....:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:...:.:.:.:...~.~.....:.: . . . . . . . . . . . . . . . . . . . . . . . . . . ‘..cc:.c:’ ?!,.:. 
.““““‘5”“““i”.‘.’ -vc....

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INS’IALIATION & MAINTENANCE 
10.80 SYSTEM SPEED-DIAL NUMBERS: 
To 
program a number, select the desired number in the list 
box shown on the previous page. The following window 
appears. 
Name: -1 Tenant: II 
NBmber: 
0 ok I 
0 &Eel 
NAME: lf desired, select the Name text box and 
type the desired name up to 16 characters. 
TENANT If the number 
is to be used exclusively by 
one tenant group, select the Tenant text box and type 
the...