Inter-Tel Imx/Gmx 416/832 Installation Manual

PROGRAMMING INTER-TELPRACTICES 
Issue 1, November 1994 
lMX/GMX 416/832 lNSTALL.ATION & MAINTENANCE 
12. LEAST-COST ROUTING (LCR) 
12.1 Programming LCR requires some preparation. 
Refer to page 4-32 in m for a description of 
the feature. Then, follow the planning steps listed be- 
low. For a program plamring sheet, refer to Figure S-23, 
on page 5-228. 
Facility groups: Determine the types of trunk 
groups 
available and assign them to up to 24 facility 
groups (32 in an expanded system). For example,...

INTER-TELPRACTICES PROGRAMMING 
IMWGMX 416/832 INSTALLATION % MAINTENANCE Issue 1, November 1994 
Actions setup Exit 
Route Groups 
Dial Rules 
~ . . . . . . . . ../............................... ~ ~ ,.................._...._ :i 
02 Echo Area Code 
03 Echo Lot Address 
04 Echo Extension Number 
05 
06 
07 
OS 
12.2 The window shown above can be reached by 
selecting Least-Cost Routing from the Applications 
menu or entering the LCR command. 
123 ROUTE GROUPS: The 
Route Croups list box 
shows each group...

PROGRAMMING INTER-TELPRACTICES 
Issue 1, November 1994 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
&scription: 
Area/Off& Code Table 
Excluded 
included Qmfiguration 
I None 
Time Block 
Ordered List 
B. ROUTE GROUPS 
12.9 DESCRIPTION: 
To give the route group a 
name of up to 
20 characters, select the Description text 
box and type the name. 
12.10 CONF’IGURA’I’ION: To assign area and office 
codes to tables, or to assign facility groups to time 
blocks, select the desired line in the Configuration...

PROGRAMMING 
INTER-TELPRACTICES 
Issue 1, November 1994 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
l ALL or NONE: To place all trunk groups in the 
facility group, select the All command button. To re- 
move all trunk groups from the facility group, select 
the None command button. 
NOTE: If more than one trunk group is placed in a 
facility group, the trunk groups will be accessed in 
numerical order by the station users. If you wish to 
have them a ccessed 
in a different order, place each 
trunk...

INTER-TEL PRACTICES PROGRAMMING 
IMX/GMX 416/832 INSTALLATION & -ANCE Issue 1, November 1994 
13. TRUNK PROGRAMMING 
13.1 When Trunk Programming is selected from the 
Applications Menu window, the menu expands to show 
the following options: 
Trunk Programming... 
Individual Trunk 
Trunk Groups, DID Groups, And 
Ring-in/Answer Patterns 
Tl Programming 
13.2 Each of the options and the windows they access 
are described in detail in the following pages. Program 
pl- sheets for trunk programming are in...

I 
I 
PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
Actions SetuD Exit 
XXXX G/L 
xX.xX G/L 
xX.xX G/L 
xX.xX G/L 
xX.xX G/L 
xX.X.X DID 
xX.xX DID 
xX.xX DID 
xX.xX DID 
xX.xX DID 
( Exit 1 Group& 01 
I.-l 
Receive Gain: 
cl 0 dB 
0 Ground Start 
Tram&t Gain: 
l-l 0 dB 
0 a LQopstart 
I Hybrid Balance - 
0 Ideal 
0 l Unloaded 
0 Loaded 
E E & M Interface 
I Current DT Detect 
- 
I Relaxed Ring Detect 
w QTMF Signaling 
q Ignore Answer supervision 
I...

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRAcTIcES 
IMX/GMX 416/832 INSTALLXITON & MAINTENANCE 
B. TRUNK GROUPS, DID GROUPS, AND 
modes, or any combination of the following can be 
RlNGJN/ANSWER PAlTERNS (TRN?Q used. 
13.16 When you select Trunk Groups, DID Groups, 
and Ring-In/Answer Patterns from the Trunk Program- 
ming menu, or enter the TRNK command, the window 
appears as shown on page 5-108. - Single: If the trunk group will ring at a single sta- 
tion, determine the circuit or extension...