Inter-Tel Imx/Gmx 256 Installation And Field Maintenance Manual

INTER-~PRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCElv!lAwIssue 1, November 1994
B.ADD PARTIES TO A CONFERENCE
20.6To ADD IMUlES To AN EXlSl7NG CONFERENCE (ANY
ItLSLDE R4Rl-Y):
NOTE: Only one party in the conference can perform
this 
prwedure at a time. This procedure cannot be per-
formed if the maximum number of conference partici-
pants has been reached.
Keysetz
(1)During the conference, press the CNP key. Theother parties remain connected. The 
CNP key
flutters.
(2)Place an intercom or outside call...

INTER-TELPRACTICESIM.X/GMX 256 INSTALLATION & MATNTENANCE
(2)Return to the parties one at a time:
Keysetz Access one party by pressing the flutter-
ing call or individual trunk key or 
IC key. Then
you 
can place it on hold, disconnect it, or re-es-
tablish the conference (following the procedures
in paragraph 20.5). Repeat this step to access the
secondparty.
Siie-Line Set: Access one party by pressing
the ESLS HOLD key or by pressing the FLASH
(hookflash) key and then pressing the HOLD key
(or entering...

FEATURESIssue 1, November 1994
21. SYSTEM FORWARDING
21.1System forwarding provides the ability to pro-
gram the system so that calls ringing at a station will fol-low a database-programmed “forwarding path” that
routes the call based on the type of call and the status ofthe intended station. (“Manual” Call Forwarding can
also be used at stations with system forwarding.) Sever-
al terms will be used to describe this feature, including:lPrincipal Station: Original station being called.
0 Forwarding Point:...

FEATURESIssue 1, November 1994INTER-TELPRACTICESIMX/GMX 256 lNST4LL.4TION & MAINTENANCE
Hanclsfme Announce System Forward Option
21.8When the a call is transferred to the principal
station by another station user and the princi&al sta-
tion%systemforwardiksetforthe %oanswer”station
s@us, a system-wide option determines what the caller
hears. If the “handsfree announce system forward” op-
tion is enabled, the transferring station user will place a
handsfree call to the principal station and can 
amrounce...

INTER-TEiLPRACmCEsIMx/GMX 256 INSTALLATION & MAINTENANCEUnanswered Calls
21.19 If a call that is following a system forwarding path is not answered or all forwarding points are in
do-not-disturb or busy, its final destination depends on the type of call as shown below.TYPE OF
CALL
IntercomALL FWD POINTS ARE BUSY OR DO NOT
ANSWERRings at the last forwarding point until it is an-
swered or the caller hangs up.
Direct ring-inReturns to the principal station and rings until
it is answered or the caller hangs...

INTER-TELPRACTICE!JlMX/GMX 256IIWhLLATION & MAINTENANCE
22. CALL FORWARDING
22.1with call forwarding, a station user can route in-coming intercom and outside calls (including direct
ring-in calls and DID calls) to another station, to a hunt
group, or to an outside telephone number, if allowed by
toll and trunk restrictions. The four forwarding options
iUCForward 
aU cak All incoming calls are immedi-
ately forwarded.
Forward if no answer: Incoming calls are
forwarded if they are not answered before the...

INTER-TELPRACTICESIMX/GMX 256 INSTALLATION & MAINTENANCEFEATURESIssue 1, November 1994
number through the other system, the E&M trunk access
code is entered, followed by the 
other system’s trunk
access code (which the 256 System has been pro-
grammed to absorb as described on page 4-26), and the
telephone 
number. Then, when a call is forwarded, thesystem automatically pauses after the E&M trunk
access code, for the duration of the Pause Digit timer,
before dialing the rest of the number.
22.14When an...

Se~ember 1994INTER-TELPR4cTIcESI.MX/GMX 256 INSTALLATION & MAINTENANCE
22.17To CAhVELAhYCALL FORWARD REQUEST:
Keyset:PressthelitFWDkey(thekeygoesofQ
If on hook, press the lit SPKR key (the key goes
off), or 
if offhook hang up. You hear a progresstone. (Display 
keysets show CANCEL ANY
CALL FORWARD.)
Single-Line Set: Lift the handset., enter the can-cel any Call Forward feature code 
(359), and
hang up.Forwarding To The Message Center
22.18Keysct users have a simple method for fonvard-
ing calls to their...

FEATURESIssue 1, November 1994
23. SPEED DIALING
23.1Three 256 System features provide speeddial-
ing. They are as follows:
System Speed Dialing: Up to 400,32-d@ system
or tenant-specific speed-dial numbers can be stored
in system memory.Station Speed Dii: Each station user 
csn pro-
gram individual speed-dial numbers. Single-line set
users can store up to 
10,16-d@ numbers. Keyset
users can store 10 outside telephone numbers (up to
16 digits each) and 10 extension numbers (up to four
digits each).System...

INTER-~PRACTICESlMX/GMX 256 INSmTION 2% MAINTENANCE
23.nTOPROGRAM OR CHANGE .WYlEbfSPERD-DL4LNuM
BRRSAND NAMES @.llENVANlSAh’D lFiEDESIGN~ SYS-
lE.MSPEED-DLALPROGRAMMNGKEYSETOW:
NOTE: If you make a mistake, use the MUTE key to
backspace. 
Or, lift and replace the handset (the name
and number in memory remains unchanged); then start
over.
(1)
(2)
(3)
(4
While on hook, Press the SYS SPD key (or press
SPCL and enter the program System Speed-Dialfeature code
- 020). (Display keysets show
PROGRAM SYSTEM SPEED...