HP Z5200 Owners Manual

8.Remove the two T-15 screws th at secure the Left Ink Supply Station to the printer.
9.Disconnect the three connectors from the Left Ink Supply Station.
NOTE: If you need to change the ISS Harness Cable,  make sure you keep the previously used
plastic connector. The new cable will arrive with  a female end, which you will replace with the
existing male end.
10. Unroute the three cables from the Left Ink Supply Station.
ENWW Left Ink Supply Station 287 

11.Carefully lift the Cartridge Tubes Connector out of the Left Ink Supply Station.
12.Carefully lift the Left Ink Supply Station enough so  that you can rotate it counterclockwise to release
the front attachment  from the printer.
13.Carefully lift the Left Ink Supply Station completely out of the printer.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide...

NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Remove the Left  Cover (refer 
Left Cover on page 188).
3. Remove the Front Panel (refer 
Front Panel on page 203).
4. Remove the Top Cover (refer 
Top Cover on page 205).
5. Open the Carriage Cover.
6.Remove all the Printheads.
7.Remove the four T-15 screws that secure the Ink Supply Tubes to the Carriage Assembly.
ENWW Ink Supply Tubes 289 

8.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time.
9.Close and lock the Carriage Assembly cover.
10.Carefully feed the Ink Supply Tubes into the print path area.
290 Chapter 6   Removal and Installation ENWW 

11.Remove the top T-15 screw that secures Ink Supply Tubes guide to the printer.
12.Remove the two front T-15 screws that secu re Ink Supply Tubes guide to the printer.
13.Carefully lift the Ink Supply Tubes guide enough until you can slide it forwards out of the printer.
ENWW Ink Supply Tubes 291 

14.Gently move the Ink Supply Tubes from the printer.
15.Use a flat bladed screwdriver  to release all the Ink Supply Tubes clamps from the printer.
16.Remove two T-10 screws that secure the right Side Plate of the Right Ink Supply Station.
292 Chapter 6   Removal and Installation ENWW 

17.Remove the Right Side Plate of the Right Ink Supply Station.
18.Remove two T-10 screws that secure the left  Side Plate of the Right Ink Supply Station.
19.Remove the Right Ink Supply Station bonding cable.
ENWW Ink Supply Tubes 293 

20.Remove the left Side Plate of the Right Ink Supply Station.
21.Carefully lift the Cartridge Tubes Connecto r out of the Right Ink Supply Station.
22.Remove two T-10 screws that secure the left  Side Plate of the Left Ink Supply Station.
294 Chapter 6   Removal and Installation ENWW 

23.Remove the left Side Plate of the Left Ink Supply Station.
24.Remove two T-10 screws that secure the right Side Plate of the Left Ink Supply Station.
25.Remove the Left Ink Supply Station bonding cable.
ENWW Ink Supply Tubes 295 

26.Remove the right Side Plate of the Left Ink Supply Station.
27.Carefully lift the Ink Supply  Tubes out of the printer.
NOTE:When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
Formatter
Removal
NOTE:Switch off the printer and remove the power cable.
1.Fully loosen the two locking thumbscrews that secure the Formatter in...