HP Z5200 Owners Manual

20.Carefully unroute the Color Sensor (ESP)  cable from the Carriage Assembly.
21.Remove one T-10 screw that  secures the Color Sensor (ESP)  to the Carriage Assembly.
22.Remove the Color Sensor (ESP) from Carriage Assembly.
NOTE: When you reinstall the Color  Sensor (ESP), be very careful not to overtighten the
attachment screw because this will damage cause irreparable damage to it.
Take care when you route the Colo r Sensor (ESP) cable so it lays flat and is not twisted. This
ensures that when you...

NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Remove the Left Cover (refer 
Left Cover on page 188).
3. Remove the Front Panel (refer 
Front Panel on page 203).
4. Remove the Top Cover (refer 
Top Cover on page 205).
5. Remove the Window Position Sensor (refer 
Window Position Sensor on page 208).
6. Remove the Ink Supply Tubes Support Rail (refer 
Ink Supply Tubes Support Rail on page 209).
7. Open the Carriage Cover.
8.Remove all...

10.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time.
11.Close and lock the Carriage Cover.
12.Carefully move the Ink Supply Tubes into the print path.
ENWW Line Sensor 269 

13.Unclip and slide off the small cover of the Carriage Assembly Carriage PCA.
14.Remove one T-15 screws that secures the large cover of the Carriage PCA.
15.Remove the large cover of the Carriage PCA.
270 Chapter 6   Removal and Installation ENWW 

16.Disconnect the Line Sensor electrical connection from the Carriage PCA.
17.Carefully unroute the Line Sensor  cable from the Carriage Assembly.
18.Remove one T-10 screw that secures the  Line Sensor to the Carriage Assembly.
ENWW Line Sensor 271 

19.Remove the Line Sensor from Carriage Assembly.
NOTE: When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
Carriage Cover (includes Carriage Latch)
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the Right Cover (refer Right Cover on page 185).
2. Remove the Left Cover (refer 
Left Cover on page...

8.Remove all the Printheads.
9.Remove the four T-15 screws that secure the Ink Supply Tubes to the Carriage Assembly.
10.Carefully lift out the Ink Supply Tubes and close the carriage cover at the same time.
ENWW Carriage Cover (includes Carriage Latch) 273 

11.Close and lock the Carriage Cover.
12.Carefully move the Ink Supply  Tubes into the print path.
13.Unclip and slide off the small cover of the Carriage Assembly Carriage PCA.
274 Chapter 6   Removal and Installation ENWW 

14.Remove one T-15 screws that secures the large cover of the Carriage PCA.
15.Remove the large cover of the Carriage PCA.
16.Disconnect the six ribbon cables of Carr iage Cover from the Carriage Assembly PCB.
ENWW Carriage Cover (includes Carriage Latch) 275 

17.Remove six T-10 screws that secure  the Carriage Assembly Cover hinge.
18.Carefully lift the Carriage Cover in  the vertical position to remove it from the Carriage Assembly.
NOTE:When you finish installing or  replacing this component, you must perform the necessary
Service Calibrations. To find which ca librations you must perform, refer to 
Service Calibration Guide to
Removal and Installation on page 170.
Carriage PCA
Removal
NOTE:Switch off the printer and remove the power cable.
1.Remove the...