HP P3015 Service Manual

I/O menuItems on the I/O (input/output) menu affect the communication between the product and the computer.
If the product contains an HP Jetdirect print server, you can configure basic networking parameters by
using this submenu. You can also configure these and other parameters through HP Web Jetadmin or
the embedded Web server.
For more information on these options, see the product user guide.
To display:  Press the Menu button 
, select the  CONFIGURE DEVICE  menu, and then select the  I/
O  menu....

ItemSub-itemSub-itemValuesDescription
 IPV4 SETTINGSCONFIG METHODBOOTP
DHCP*
AUTO IP
MANUALSpecify the method that TCP/IPv4
parameters are configured on the
HP Jetdirect print server.
BOOTP : Automatic configuration from a
BootP (Bootstrap Protocol) server.
DHCP : Automatic configuration from a
DHCPv4 (Dynamic Host Configuration
Protocol) server. If selected and a DHCP
lease exists, the  DHCP RELEASE  and
DHCP RENEW  menus are available to set
DHCP lease options.
AUTO IP : Automatic link-local IPv4...

ItemSub-itemSub-itemValuesDescription
  DHCP RENEWYES
NO*Specify whether the print server requests to
renew the DHCP lease.
NOTE: This menu appears if the  CONFIG
METHOD  menu is set to the DHCP  option
and a DHCP lease for the print server exists.
  PRIMARY DNS Specify the IP address (n.n.n.n) of a Primary
DNS Server.
  SECONDARY DNS Specify the IP address (n.n.n.n) of a
Secondary Domain Name System (DNS)
Server.
 IPV6 SETTINGSENABLEON *
OFFEnable or disable IPv6 operation on the print
server....

ItemSub-itemSub-itemValuesDescription
 PROXY SERVER  Specifies the proxy server to be used by
embedded applications in the product. A
proxy server is typically used by network
clients for Internet access. It caches Web
pages, and provides a degree of Internet
security, for those clients.
To specify a proxy server, enter its IPv4
address or fully-qualified domain name. The
name can be up to 255 octets.
For some networks, you might need to
contact your Internet Service Provider (ISP)
for the proxy server...

ItemSub-itemSub-itemValuesDescription
 RESET SECURITY YES
NO*Specify whether the current security settings
on the print server will be saved or reset to
factory defaults.
DIAGNOSTICSEMBEDDED TESTS  This menu provides tests to help diagnose
network hardware or TCP/IP network
connection problems.
Embedded tests help to identify whether a
network fault is internal or external to the
product. Use an embedded test to check
hardware and communication paths on the
print server. After you select and enable a...

ItemSub-itemSub-itemValuesDescription
 PING TEST  Check network communications. This test
sends link-level packets to a remote network
host, then waits for an appropriate response.
To run a ping test, set the following items:
  DEST TYPEIPV4
IPV6Specify whether the target product is an IPv4
or IPv6 node.
  DEST IPV4 Type the IPv4 address.
  DEST IPV6 Type the IPv6 address.
  PACKET SIZE Specify the size of each packet, in bytes, to
be sent to the remote host. The minimum is
64 (default) and the maximum...

ItemSub-itemSub-itemValuesDescription
  RTT AVERAGE Shows the average round-trip-time (RTT),
from 0 to 4096 milliseconds, for packet
transmission and response. The default is 0.
  PING IN
PROGRESSYES
NO*Select whether the control panel indicates
when a ping test is in progress.
  REFRESHYES
NO*When viewing the ping test results, this item
updates the ping test data with current
results. A refresh automatically occurs when
the menu times out or you manually return to
the main menu.
LINK SPEED    AUTO*
10T...

Resets menuUse the RESETS  menu to reset factory settings, disable and enable sleep mode, and update the product
after new supplies are installed.
To display: Press the  Menu button 
, select the  CONFIGURE DEVICE  menu, and then select the
RESETS  menu.
NOTE: Values that have an asterisk (*) are the factory-default values. Some menu items have no
default.
ItemSub-itemValuesDescription
RESTORE FACTORY
SETTINGS  Clear the page buffer, remove all
perishable personality data,
reset the printing...

ItemSub-itemValuesDescription
 SOURCEALL TRAYS
TRAY 1
TRAY 2*
TRAY 3
TRAY 4Specifies whether the test page is
printed from all trays or from a
specific tray.
 DUPLEXOFF
ONDetermines whether the duplexer
is used in the test.
 COPIES1 *
10
50
100
500Determines how many pages
should be sent from the specified
source as part of the test.
MANUAL SENSOR TEST  Performs tests to determine
whether the paper-path sensors
are operating correctly.
MANUAL SENSOR
TEST 2  Performs additional tests to
determine whether...

Service menu
The SERVICE menu is PIN-protected for added security. Only authorized service people have access
to the  SERVICE  menu. When you select  SERVICE from the list of menus, the product prompts you to
type an eight-digit PIN number.
● The PIN for the HP LaserJet P3015 models is 07301509.
1. Press the  Menu button 
.
2. Press the down arrow 
 button or the up arrow  button to navigate to the  SERVICE menu, and
then press the  OK button.
3. Type the PIN using the alphanumeric keypad (for the base...