HP P2055 Manual

							Extended warranty
HP Support provides coverage for the HP hardware product and all HP-supplied internal components.
The hardware maintenance covers a 1- to 3-year period from date of the HP product purchase. The
customer must purchase HP Suppor t within the stated factory warranty. For more information, contact
the HP Customer Care Service and Support group.
ENWW HP maintenance agreements 289 
						

							290 Appendix A   Service and supportENWW 
						

							B Specifications
●Physical specifications
●
Electrical specifications
●
Acoustic emissions
●
Operating environment
ENWW 291 
						

							Physical specifications
Table B-1  Product dimensions and weights
Product modelHeightDepthWidthWeight
HP LaserJet P2050 Series d model268 mm (10.6 in)368 mm (14.5 in)360 mm (14.2 in)10.6 kg (23.4 lb)
HP LaserJet P2050 Series dn model268 mm (10.6 in)368 mm (14.5 in)360 mm (14.2 in)10.6 kg (23.4 lb)
HP LaserJet P2050 Series x model405 mm (15.9 in)368 mm (14.5 in)360 mm (14.2 in)14.7 kg (32.4 lb)
Optional 500-sheet feeder 140 mm (5.5 in) 368 mm (14.5 in) 360 mm (14.2 in) 4.1 kg (9.0 lb)
Table B-2  Product dimensions with all doors and trays fully opened
Product modelHeightDepthWidth
HP LaserJet P2050 Series d model268 mm (10.6 in)455 mm (17.9 in)360 mm (14.2 in)
HP LaserJet P2050 Series dn model268 mm (10.6 in)455 mm (17.9 in)360 mm (14.2 in)
HP LaserJet P2050 Series x model 405 mm (15.9 in) 455 mm (17.9 in) 360 mm (14.2 in)
Table B-3  Product dimensions and weights
Product modelHeightDepthWidthWeight
HP LaserJet P2030 Series Printers 256 mm (10.1 in) 368 mm (14.5 in) 360 mm (14.2 in) 9.9 kg (21.8 lb)
Table B-4  Product dimensions with all doors and trays fully opened
Product modelHeightDepthWidth
HP LaserJet P2030 Series Printers 256 mm (10.1 in) 455 mm (17.9 in) 360 mm (14.2 in)
Electrical specifications
WARNING!Power requirements are based on the countr y/region where the product is sold. Do not
convert operating voltages. This might dama ge the product and void the product warranty.
Table B-5  Electrical specifications
Item110-volt models220-volt models
Power requirements100 to 127 V (+/-10%)
50 to 60 Hz (+/-2 Hz)220 to 240 V (+/-10%)
50 to 60 Hz (+/-2 Hz)
Minimum recommended circuit capacity 6.0 A 3.0 A
292 Appendix B   Specifications ENWW 
						

							Table B-6  Power consumption (average, in watts) 1,4
Product ModelPrinting2,3Ready/Sleep2Off2
HP LaserJet P2050 Series Printers57080.4
HP LaserJet P2030 Series Printers 550 70.4
1Values are based on preliminary data. Go to www.hp.com/support/ljp2050series or www.hp.com/support/ljp2030series  for
current information.
2The power reported is the highest values measured for all product models using all standard voltages.3Ready and Sleep mode power consumption is t he same with Instant On Fusing technology.4Maximum heat dissipation for all models in Ready mode = 28 BTU/Hour.
Acoustic emissions
Table B-7  HP LaserJet P2050 Series Printers1,2
Sound power levelDeclared per ISO 9296
PrintingLWAd = 6.8 Bels (A) [68 dB (A)]
ReadyLWAd = Inaudible
Sound pressure level - bystander positionDeclared per ISO 9296
PrintingLpAm = 55 dB (A)
Ready LpAm = Inaudible
1Values are based on preliminary data. Go to www.hp.com/support/ljp2050series for current information.2Configuration tested: HP LaserJet P2055dn printing simplex on A4 paper.
Table B-8  HP LaserJet P2030 Series Printers1,2
Sound power levelDeclared per ISO 9296
PrintingLWAd = 6.8 Bels (A) [68 dB (A)]
ReadyLWAd = Inaudible
Sound pressure level - bystander positionDeclared per ISO 9296
PrintingLpAm = 54 dB (A)
Ready LpAm = Inaudible
1Values are based on preliminary data. Go to www.hp.com/support/ljp2030series for current information.2Configuration tested: HP LaserJet P2035 printer printing on A4 paper.
Operating environment
Table B-9  Necessary conditions
Environmental condition PrintingStorage/standby
Temperature (product and print
cartridge)7.5° to 32.5°C (45.5° to 90.5°F)0° to 35°C (32° to 95°F)
Relative humidity 10% to 80%10% to 90%
ENWW Acoustic emissions 293 
						

							294 Appendix B   SpecificationsENWW 
						

							C Regulatory information
●FCC regulations
●
Declaration of conformity
●
Safety statements
ENWW 295 
						

							FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If this equipment is not installed a nd used in accordance with the instructions, it may
cause harmful interference to radio communications.  However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does caus e harmful interference to radio or
television reception, which can be determined  by turning the equipment off and on, the user is
encouraged to try to correct the interference  by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase separation between equipment and receiver.
● Connect equipment to an outlet on a circuit differen
t from that to which the receiver is located.
● Consult your dealer or an experienced radio/TV technician.
NOTE:
Any changes or modifications to the printer that are not expressly approved by HP could void
the user’s authority to operate this equipment.
Use of a shielded interface cable is required to comply  with the Class B limits of Part 15 of FCC rules.
296 Appendix C   Regulatory information ENWW 
						

							Declaration of conformity
Declaration of conformity
Declaration of Conformity
according to ISO/IEC 17050-1 and EN 17050-1, DoC#: BOISB-0801-00-rel.1.0
Manufacturers Name:Hewlett-Packard Company
Manufacturers Address: 11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name: HP LaserJet P2050 Series
   
Regulatory Model Number
2): BOISB-0801-00
Including CE464A — Optional 500-sheet input tray
Product Options: ALL
Print Cartridges: CE505A, CE505X
conforms to the following Product Specifications:
Safety: IEC 60950-1:2001 / EN60950-1: 2001 +A11 IEC 60825-1:1993 +A1 +A2 / EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC: CISPR22:2005 / EN 55022:2006 - Class B
1)
EN 61000-3-2:2000 +A2
EN 61000-3-3:1995 +A1
EN 55024:1998 +A1 +A2
FCC Title 47 CFR, Part 15 Class B / ICES-003, Issue 4
GB9254-1998, GB17625.1-2003
Supplementary Information:
The product herewith complies with the requirements of the EMC  Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC,  and
carries the CE-Marking 
 accordingly.
This Device complies with Part 15 of the FCC Rules. Operation  is subject to the following two conditions: (1) this device may n ot cause harmful
interference, and (2) this device must acc ept any interference received, including interference that may cause undesired operat ion.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) For regulatory purposes, this product is assigned a Regulator y model number. This number should not be confused with the mar keting
name or the product number(s).
Boise, Idaho , USA
October 22, 2007
For regulatory topics only:
European Contact: Your Local Hewlett-Packard Sales and Service  Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe,, Herrenberger Strasse 140, , D-71034, Böblingen, (FAX: +49-7031-14-3143), 
http://www.hp.com/go/certificates
USA Contact: Product Regulations Manager, Hewlett-Packard Co mpany,, PO Box 15, Mail Stop 160, Boise, ID 83707-0015, , (Phone:
208-396-6000)
ENWW Declaration of conformity 297 
						

							Safety statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has
implemented regulations for laser products manufactured since August 1, 1976. Compliance is
mandatory for products marketed in the United States. Th e device is certified as a “Class 1” laser product
under the U.S. Department of Health and Human  Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safe ty Act of 1968. Since radiation emitted inside the
device is completely confined wi thin protective housings and external covers, the laser beam cannot
escape during any phase of normal user operation.
WARNING! Using controls, making adjustments, or perfor ming procedures other than those specified
in this user guide may result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class B requirements.
« Conforme à la classe B des no rmes canadiennes de compatibilité  électromagnétiques. « CEM ». »
VCCI statement (Japan)
Power cord statement (Japan)
EMI statement (Korea)
298 Appendix C   Regulatory information ENWW