HP LaserJet M5025 User Manual

5.Touch TCP/IP.
6.Touch IPV4 Settings.
7.Touch Config Method.
8.Touch Manual.
9.Touch Save.
10.Touch Manual Settings.
11.Touch Default Gateway.
12.Touch the Default Gateway text box.
13.Use the touchscreen keyboard to type the default gateway.
14.Touch OK.
15.Touch Save.
Configure TCP/IPv6 parameters
For information about configuring the device for a TCP/IPv6 network, see the HP Jetdirect Embedded
Print Server Administrators Guide.
Disable network protocols (optional)
By factory default, all supported...

7.Touch Off.
8.Touch Save.
Disable AppleTalk
1.Scroll to and touch Administration.
2.Scroll to and touch Initial Setup.
3.Touch Networking and I/O.
4.Touch Embedded Jetdirect.
5.Touch AppleTalk.
6.Touch Enable.
7.Touch Off.
8.Touch Save.
Disable DLC/LLC
1.Scroll to and touch Administration.
2.Scroll to and touch Initial Setup.
3.Touch Networking and I/O.
4.Touch Embedded Jetdirect.
5.Touch DLC/LLC.
6.Touch Enable.
7.Touch Off.
8.Touch Save.
HP Jetdirect EIO print servers
HP Jetdirect print servers...

4 Media and trays
●General guidelines for media
●
Considerations for special media
●
Select print media
●
Printing and paper-storage environment
●
Load media into the input trays
●
Load documents for faxing, copying, and scanning
●
Print on rotated media
●
Print full-bleed images
●
Print on custom-size media
●
Control print jobs
ENWW61
 

General guidelines for media
Hewlett-Packard Company recommends testing any paper before buying it in large quantities.
CAUTIONUsing media that does not conform to the specifications listed here or in the
HP LaserJet Printer Family Print Media Guide can cause problems that require service. This
service is not covered by the Hewlett-Packard warranty or service agreements. To download a
copy of the guide, go to 
www.hp.com/support/ljpaperguide.
Paper to avoid
The product can handle many types of paper....

General media specifications
For complete paper specifications for all HP LaserJet devices, see the HP LaserJet Printer Family Print
Media Guide (available at 
www.hp.com/support/ljpaperguide) .
CategorySpecifications
Acid content5.5 pH to 8.0 pH
Caliper0.094 to 0.18 mm (3.0 to 7.0 mils)
Curl in reamFlat within 5 mm (0.02 in)
Cut edge conditionsCut with sharp blades with no visible fray.
Fusing compatibilityMust not scorch, melt, offset, or release hazardous emissions when heated to 200°
C (392°F) for...

Considerations for special media
Table 4-1  Media considerations
Media typeConsiderations
Envelopes●Use only tray 1 to print envelopes. Choo
se envelopes in the printer driver (see Select the correct
printer driver).
● Prior to printing, envelopes should lie flat wi
th less than 6 mm (0.25 in) curl, and should not
contain air.
● Envelopes should not be wrinkled,
 nicked, or otherwise damaged.
● Envelopes with a peel-off adhesive strip or with mo
re than one flap that folds over to seal must
use adhesives...

Media typeConsiderations
CAUTIONFailure to follow these guidelines can damage the device.
If a sheet of labels becomes jammed in the device, see 
Clear jams.
NOTEChoose labels in the printer driver (see Open the printer drivers).
Transparencies●Print transparencies from tray 1.
●Use only transparencies specified for use with HP LaserJet printers
●Remove transparencies from the output bin as they are printed to prevent them from sticking
together.
●Place transparencies on a flat surface after removing...

Media typeConsiderations
To avoid problems when using preprinted forms, embossed paper, and letterhead, observe the
following guidelines:
●Use preprinted forms and letterhead paper that have been printed by offset lithography or
engraving.
●When the form is preprinted, be careful not to change the moisture content of the paper, and do
not use materials that change the papers electrical or handling properties. Seal the forms in
moisture-proof wrap to prevent moisture changes during storage.
NOTETo print a...

Select the correct fuser mode
The device automatically adjusts the fuser mode based on the media type to which the tray is set. For
example, heavy paper, such as card stock, might need a higher fuser-mode setting in order to make the
toner adhere better to the page, but transparencies need a lower fuser-mode setting to avoid damage
to the device. The default setting generally provides the best performance for most print-media types.
The fuser mode can be changed only if the media type has been set for...

Select print media
This device accepts a variety of media, such as cut-sheet paper, including up to 100% recycled fiber
content paper; envelopes; labels; transparencies; and custom-size paper. Properties such as weight,
composition, grain, and moisture content are important factors that affect device performance and output
quality. Paper that does not meet the guidelines that are outlined in this manual can cause the following
problems:
●Poor print quality
●Increased jams
●Premature wear on the device,...