HP LaserJet M5025 User Manual

Load documents for faxing, copying, and scanning
Load a document onto the scanner glass
Use the scanner glass to copy, scan, or fa x small, lightweight (less than 60 g/m2 or 16 lb), or irregularly-
sized originals such as receipts, newspaper clippings, photographs, or old or worn documents.
1. Open the ADF lid.
2.Place the document face-down on th e scanner glass, as shown below:
● For letter- and A4-size documents, place the top 
right-hand corner of the document at the
back, left corner of the scanner...

●For 
rotated  letter- and A4-size documents, place the top  left-hand corner of the document at
the back, left corner of the scanner glass. Also use this orientation for B5-size media and for
custom-size media that is less than 210 mm (8.25 inches) in width.
NOTE Make sure that the media in the input tr ay is loaded in the rotated orientation.
●For legal-size, 11 x 17, and A3-size documents, place the top left-hand corner of the document
at the back, left corner of the scanner glass.
3.
Close the ADF...

Load the automatic document feeder (ADF)
Use the ADF to copy, scan, or fax a document that has up to 50 pages (depending on the thickness of
the pages).
1.Load the document face up in the ADF as shown below:
● For letter- and A4-size documents, insert the long edge of the document into the ADF with
the top of the document toward the back of the device.
●
For 
rotated  letter- and A4-size documents, insert the  short edge (the top of the document) into
the ADF.
ENWW Load documents for faxi ng, copying,...

●For legal-size, 11 x 17, and A3-size documents, insert the short edge (the top of the document)
into the ADF.
2.
Slide the stack into the ADF until it does not move any farther.
3. Adjust the media guides until they are snug against the media.
82 Chapter 4   Media and trays ENWW
 

Print on rotated media  
The device can print on letter, A4, A5, Executive, and B5 (JIS) print media in a rotated orientation (short-
edge first) from tray 1 and from  tray 2. Printing on rotated media is  slower. Some types of media feed
better when rotated, such as prepu nched paper (especially when it is printed on both sides from the
optional duplexer) or labels that do not stack flat.
NOTE To print on  rotated A5, Executive, or B5 media, configure the media size as  Custom in
the printer driver....

Print full-bleed images 
Full-bleed images extend from edge to edge of the page. To achieve this effect, use larger paper, then
trim its edges to the desired size.
CAUTIONNever print directly to the edge of paper. This causes toner to accumulate inside the
device, which may affect print quality and damage the device. Print on paper up to 312 x 470 mm
(12.28 x 18.5 in), leaving margins on all four sides of at least 2 mm (0.08 in).
NOTEWhen printing paper wider than 297 mm (11.7 in), do not use the...

Print on custom-size media  
Custom-size paper can be printed from any of the trays. For media specifications, see Media and
trays.
NOTEVery small or very large custom-size paper should be printed from tray 1. The control
panel can be set for one custom size at a time. Do not load more than one size of custom paper
into the device.
For best printing performance when you print large numbers of small or narrow media and standard
paper, print the standard paper first and then print the small or narrow...

Load custom-size media into tray 1
Load custom-size media in tray 1 using the same procedures as for standard-size media. See Load
tray 1 (multipurpose tray).
Load custom-size media into trays  2 and 3 (and optional trays 4, 5,
and 6)
1. Pull open the tray and remove any media.
2.Press the tab on media guide in the front of the tr ay and slide it so that the pointer shows a size
larger than the paper size. Also adjust the side  media-width guide to a size larger than the paper
size that you are loading....

3.Place the media in the tray and make sure that it  is flat at all four corners. Keep the stack below
the height tabs on the paper-lengt h guide in the rear of the tray.
4.On the paper-length guide, press the tab and slide  it up against the edge of the stack. Also slide
the side media-width guides up against the edge of the stack.
5. Slide the tray into the device.
ENWW Print on custom-size media 87
 

Control print jobs
When a job is sent to the printer, the printer driver controls what paper tray is used to pull media through
the printer. By default, the printer automatically selects the tray, but a specific tray can be chosen based
on three user-specified settings: Source, Type, and Size. These settings are available from the
Application Setting dialog box, the Print dialog box, or the printer driver. 
SettingDescription
SourceDirects the printer to pull paper from a user-specified tray. The
printer...