HP LaserJet M5025 User Manual

Menu itemSub-menu itemValuesDescription
Medium (default)
Darkcurves, and edges. All print resolutions, including
FastRes 1200, benefit from REt.
Economode Enabled
Disabled (default)When Economode is enabled, the device prints with a
reduced amount of toner per page; however, the print
quality of the page is slightly reduced.
Toner Density Choose from a range of 1
to 5. 3 is the default.Lighten or darken the print on the page. 1 is the lightest
and 5 is the darkest.
Calibration/Cleaning Auto...

Troubleshooting menu
NOTEValues shown with (default) are the factory-default values. Some menu items have no
default.
Table 2-16  Troubleshooting menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Event Log  Print (button)Use this feature to show the 50 most recent
events in the event log.
Touch Print to print the full event log.
Calibrate Scanner  CalibrateUse this feature to compensate for offsets in
the scanner imaging system (carriage head)
for ADF and flatbed scans.
You might need to...

Menu itemSub-menu itemSub-menu itemValuesDescription
Paper Path Test
Test Page Print (button)Generate a test page for testing paper
handling features. You can define the path
that is used for the test in order to test specific
paper paths.
Source All trays
Tray 1
Tray 2
(Additional trays are
shown, if applicable.)Specify whether the test page will be printed
from all trays or from a specific tray.
Destination A list of output bins
appears.Select the output option for the test page. You
can choose to send...

Menu itemSub-menu itemSub-menu itemValuesDescription
Finishing Paper Path
TestStaplingFinishing OptionsChoose from a list of
available options.Test paper handling features for the finisher.
Select the option that you want to test.
Media SizeLetter
Legal
A4
Executive (JIS)
8.5 x 13Select the paper size for the Finishing Paper
Path Test.
Media Type Select the paper type for the Finishing Paper
Path Test.
Copies Select the number of copies to include in the
Finishing Paper Path Test.
DuplexOff
OnSelect...

Menu itemSub-menu itemSub-menu itemValuesDescription
Print/Stop Test  Continuous value
from 0 to 60,000
milliseconds. The
default is 0
milliseconds.Isolate faults by stopping the device during
the print cycle and observing where in the
process the image degrades. To run the test,
specify a stop time. The next job that is sent
to the device will stop at the specified time in
the process.
Scanner Tests   This menu item is used by a service
technician to diagnose potential problems
with the device scanner....

Resets menu
Table 2-17  Resets menu
Menu itemValuesDescription
Clear Local Address BookClear (button)Use this feature to clear all addresses from the address books that
are stored on the device.
Clear Fax Activity LogYes
No (default)Use this feature to clear all events from the Fax Activity Log.
Restore Factory Telecom SettingRestore (button)Use this option to restore the telephone-related settings that are in
the Initial Setup menu to factory default values.
Restore Factory SettingsRestore (button)Use...

3 I/O Configuration
●USB configuration
●
Network configuration
ENWW55
 

USB configuration
This device supports a USB 2.0 connection. You must use an A-to -B type USB cable for printing.
Figure 3-1  USB connection
1USB connector
2USB port (type B)
56 Chapter 3   I/O Configuration ENWW
 

Network configuration
You might need to configure certain network parameters on the device. You can configure these
parameters in the following locations:
●Installation software
●Device control panel
●Embedded Web server
●Management software (HP Web Jetadmin or HP LaserJet Utility for Macintosh)
NOTEFor more information about using the embedded Web server, see Use the embedded
Web server
For more information on supported networks and network configuration tools, see the HP Jetdirect Print
Server...

6.Touch IPV4 Settings.
7.Touch Config Method.
8.Touch Manual.
9.Touch Save.
10.Touch Manual Settings.
11.Touch IP Address.
12.Touch the IP Address text box.
13.Use the touchscreen keypad to type the IP address.
14.Touch OK.
15.Touch Save.
Set the subnet mask
1.Scroll to and touch Administration.
2.Scroll to and touch Initial Setup.
3.Touch Networking and I/O.
4.Touch Embedded Jetdirect.
5.Touch TCP/IP.
6.Touch IPV4 Settings.
7.Touch Config Method.
8.Touch Manual.
9.Touch Save.
10.Touch Manual Settings....