HP LaserJet M5025 User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
100TX Auto: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full: 1000 Mbps, full-duplex operation.
Print Protocols    Use this item to print a page that lists the configuration
of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
Table 2-10  Jetdirect menus (continued)
ENWW Use the Administration menu 39
 

Fax Setup
Table 2-11  Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Required SettingsLocation (Countries/regions
listed)Configure the settings that are legally
required for outgoing faxes.
Date/Time  
Fax Header
InformationPhone Number
Company Name 
PC Fax Send  Disabled
Enabled (default)Use this feature to enable or disable PC Fax
Send. PC Fax Send enables users to send
faxes through the device from their
computers if they have the correct driver
installed.
40 Chapter 2   Control...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Send SettingsFax Dial Volume Off
Medium (default)
HighUse this feature to set the volume of the tones
that you hear while the device dials the fax
number.
Error Correction
Mode Enabled (default)
DisabledWhen Error Correction Mode is enabled and
an error occurs during fax transmission, the
device sends or receives the error portion
again.
JBIG Compression Disabled
Enabled (default)The JBIG Compression reduces fax-
transmission time, which can result...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Receive Settings
Rings To Answer The range varies by
location. The factory
default is 2 rings.Use this feature to specify the number of rings
that must occur before the fax modem
answers.
Ring Interval Default (default)
CustomUse this feature to control the time between
rings for incoming faxes.
Ringer Volume Off
Low (default)
HighSet the volume for the fax ring-tone.
Blocked Fax
NumbersAdd Blocked
NumbersType the fax number
to add.Use this feature...

E-mail Setup
Use this menu to enable the e-mail feature and to configure basic e-mail settings.
NOTETo configure advanced e-mail settings, use the embedded Web server. For more
information, see 
Use the embedded Web server.
Table 2-12  E-mail Setup menu
Menu itemValuesDescription
Address ValidationOn (default)
OffThis option enables the device to check e-mail syntax when you type
an e-mail address. Valid e-mail addresses require the @ sign and
a ..
Find Send Gateways Search the network for SMTP gateways...

Device Behavior menu
NOTEValues shown with (default) are the factory-default values. Some menu items have no
default.
Table 2-14  Device Behavior menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Language  Select the language
from the list.Use this feature to select a different language
for control-panel messages. When you select
a new language, the keyboard layout might
also change.
Key Press Sound  On (default)
OffUse this feature to specify whether you hear
a sound when you touch the screen or...

Menu itemSub-menu itemSub-menu itemValuesDescription
Tray BehaviorUse Requested Tray Exclusively (default)
FirstUse this feature to control how the device
handles jobs that have specified a specific
input tray.
Manually Feed
Prompt Always (default)
Unless LoadedUse this feature to indicate whether a prompt
should appear when the type or size for a job
does not match the specified tray and the
device pulls from the multipurpose tray
instead.
PS Defer Media Enabled (default)
DisabledUse this feature to...

Menu itemSub-menu itemSub-menu itemValuesDescription
General Copy
BehaviorScan Ahead Enabled (default)
DisabledUse this feature to turn on no-wait scanning.
With Scan Ahead enabled, the pages in the
original document are scanned to disk and
held until the device becomes available.
Auto Print Interrupt Enabled
DisabledWhen this feature is enabled, copy jobs can
interrupt print jobs that are set to print multiple
copies.
The copy job is inserted into the print queue
at the end of one copy of the print job....

Menu itemSub-menu itemSub-menu itemValuesDescription
 PCL Form LengthType a value
between 5 and 128
lines. The factory
default is 60 lines.PCL is a set of printer commands that
Hewlett-Packard developed to provide
access to printer features.
OrientationPortrait (default)
LandscapeSelect the orientation that is most often used
print jobs. Select Portrait if the short edge is
at the top or select Landscape if the long edge
is at the top.
Font SourceSelect the source
from the list.Use this feature to select...

Print Quality menu
NOTEValues shown with (default) are the factory-default values. Some menu items have no
default.
Table 2-15  Print Quality menu
Menu itemSub-menu itemValuesDescription
Set RegistrationSourceAll trays
Tray : 
(choose a tray)Use Set Registration to shift the margin alignment to
center the image on the page from top to bottom and
from left to right. You can also align the image on the
front with the image printed on the back.
Select the source input tray for printing the Set
Registration...