HP LaserJet 9059 MFP User Manual

Economy settings
Sleep and wake
Set the sleep delayUse the sleep-delay feature to set the period of time that the MFP must be idle before it enters the sleep
mode. The default setting is 45 minutes.
1.Scroll to and touch  Administration.
2. Touch  Time/Scheduling .
3. Touch  Sleep Delay .
4. Touch the sleep-delay setting that you want.
Set the sleep time Use the sleep time feature to put the MFP in sleep mode at a set time each day.
1.Scroll to and touch  Administration.
2. Touch  Time/Scheduling .
3....

7.Touch the appropriate options to set the correct hour, minute, and AM/PM setting.
8. If you want to wake the MFP at the same time every day (including weekends), on the  Apply to
All Days  screen, touch  Yes. If you want to set the time for individual days, touch  No, and repeat
the procedure for each day.
178 Chapter 11   Manage and maintain ENWW
 

12 Problem solve
●Solve problems
●
Determining Solve MFP problems
●
Control-panel message types
●
Control-panel messages
●
Clear jams
●
Media-handling problems
●
Solve print-quality problems
●
Solve fax problems
●
Solve copy problems
●
Solve e-mail problems
●
Solve network connectivity problems
●
Solve common Macintosh problems
ENWW 179
 

Solve problems
If the MFP is not responding correctly, complete the steps in the following checklist, in order. If the MFP
does not pass a step, follow the corresponding troubleshooting suggestions. If a step resolves the
problem, you can stop without performing the other steps on the checklist.
Troubleshooting checklist
1.Make sure that the MFP Ready light is on. If no lights are on, complete these steps:
a.Check the power-cable connections.
b. Check that the power switch is on.
c. Check the power...

Determining Solve MFP problems
Situation/MessageSolution
The control-panel display is blank, and internal fans are not
running.Make sure that the MFP power is on. Press all the keys to see
if one is stuck. Contact your HP-authorized service
representative if these steps do not work.
The MFP is turned on, but the internal fans are not running.Make sure that the line voltage is correct for the MFP power
configuration. (See the label on the back of the device for
voltage requirements.) If you are using a...

Control-panel message types
Four types of control-panel messages can indicate the status of or problems with the device.
Message typeDescription
Status messagesStatus messages reflect the current state of the device. They inform you of normal device operation
and require no interaction to clear them. They  change as the state of the device changes. Whenever
the device is ready, not busy, and has no pending warning messages, the status message  Ready
appears if the device is online.
Warning...

Control-panel messages
The product provides robust control panel messaging. When a message appears on the control panel,
follow the on-screen instructions to resolve the issue. If the product displays an “Error” or “Attention”
message, and no steps are shown to resolve the issue, turn the product off then on. Contact your dealer
for support if you continue to experience issues with the product.
To get additional information for warnings that appear in the status line, touch the Warning button 
.
For...

Clear jams
If a jam message appears on the control panel, look for media in the locations indicated in the following
illustration. You might need to look for jammed media in locations other than those that are indicated in
the jam message. If the location of the jam is not obvious, look first in the front door area.
After looking at the illustration, you can go to the procedure for clearing the jam. When clearing jams,
be very careful not to tear the media. If a small piece of media remains in the MFP,...

Clear jams from the duplexer
1.Move the output device away from the MFP to gain access to the left door.
Figure 12-2  Clear jams in the duplex printing accessory (1 of 6)
2.Open the left door and carefully pull out any paper from area.
WARNING! Avoid touching the adjacent fusing area. It can be hot.
Figure 12-3  Clear jams in the duplex printing accessory (2 of 6)
3.Remove the duplex printing accessory by pressing the green lever and pulling the unit out until it
stops.
Figure 12-4  Clear jams in the...

6.Check for paper in the duplex printing accessory area, and remove any paper by pulling it out of
the MFP. Be careful not to tear the paper.
Figure 12-6   Clear jams in the duplex printing accessory (5 of 6)
7.Reinstall the duplex printing accessory by sliding it back into the slot until it locks into place.
Figure 12-7   Clear jams in the duplex printing accessory (6 of 6)
8.Close all open doors. Push the output device back into place.
Clear jams from the input-tray areas
Clear jams in tray 1
1.Check...