HP LaserJet 3052 User Manual

							Transparencies and labels
Only use transparencies and labels that are recommended for use in laser printers, such as
HP transparency film and HP LaserJet labels. See 
Guidelines for using media for more information.
CAUTION Be sure to set the correct media type in the all-in-one settings. The all-in-one
adjusts the fuser temperature according to the media type setting. When printing on special
media such as transparencies or labels, this adjustment prevents the fuser from damaging the
media as it passes through the all-in-one.
CAUTION Inspect the media to make sure that it is  not wrinkled or curled and that it does
not have any torn edges or missing labels.
NOTE You can load multiple transparencies in the main input tray (tray 2). However, do not
load more than 75 transparencies at a time.
Custom-size media and card stock
Use the main input tray for multiple sheets. See Supported media weights and sizes  for the
supported media sizes.
CAUTION Make sure that the sheets are not stuck together before you load them.
Colored paper
●Colored paper should be of the same high quality as white xerographic paper.
● Pigments used must be able to withstand the 
fuser temperature of 200°C (392°F) for 0.1 second
without deterioration.
● Do not use paper with a colored coating 
that was added after the paper was produced.
ENWW Printing on special media 63
 
						

							Envelopes
Only use envelopes that are recommended for laser printers. See Guidelines for using media for
more information.
NOTE For the HP LaserJet 3390/3392 all-in-one, you must load envelopes one at a time in
the single-sheet priority input slot (tray 1).
To prevent the envelope from curling as it  prints, open the rear output door (HP LaserJet 3390/3392
all-in-one).
Heavy paper
● Any tray will print most heavy media that does not exceed 105 g/m2 (28 lb bond).
● Use tray 1 for card stock (135 g/m
2 to 216 g/m2; 50 to 80 lb cover).
● In either the software program or the printer driver, select Heavy  (106 g/m
2 to 163 g/m2; 28 to
43 lb bond) or  Cardstock (135 g/m2 to 216 g/m2; 50 to 80 lb cover) as the media type, or print
from a tray that is configured for heavy paper. Because this setting affects all print jobs, it is
important to return the all-in-one back to its original settings after the job has printed.
CAUTION Using paper that is heavier than the  media specification recommended for this all-
in-one can cause misfeeds, jams, reduced print quality, and excessive mechanical wear.
Some heavier media, such as HP Cover Stock, can be safely used.
Letterhead and preprinted forms
The all-in-one can print on letterhead and preprinted forms that can withstand temperatures of 200°C
(392°F).
NOTE To print a single-page cover letter on letterhead, followed by a multiple-page
document, feed the letterhead face up in the single-sheet priority input slot (tray 1), and load
the standard paper in the main input tray  (tray 2). The all-in-one automatically prints from the
single-sheet priority input slot first.
64 Chapter 5   Printing ENWW
 
						

							Canceling a print job
If your print job is currently printing, you can cancel it by pressing Cancel on the all-in-one control
panel.
CAUTION Pressing Cancel clears the job that the all-in-one is currently processing. If more
than one process is running (for example, the all-in-one is printing a document while receiving
a fax), pressing Cancel clears the process that currently appears on the all-in-one control
panel.
You can also cancel a print job from a software program or a print queue.
To stop the print job immediately, remove the  remaining print media from the all-in-one. After printing
stops, use one of the following options:
● Device control panel:
 To cancel the print job, press and release  Cancel on the all-in-one
control panel.
● Software program:
 Typically, a dialog box appears briefly on the computer screen, allowing
you to cancel the print job.
● Windows print queue:
 If a print job is waiting in a print queue (computer memory) or print
spooler, delete the job there.
● Windows 98, Windows Me, or Windows 2000:
 Go to the Printer dialog box. Click Start,
click  Settings, and then click  Printers. Double-click the all-in-one icon to open the window,
select your print job, and then click  Delete.
● Windows XP:
 Click Start, click  Settings, and then click  Printers and Faxes. Double-click
the icon for the all-in-one to open the window,  right-click the print job that you want to
cancel, and then click Cancel .
● Macintosh print queue:
 Open the print queue by double-clicking the all-in-one icon in the dock.
Then highlight the print job and click  Delete.
ENWW Canceling a print job 65
 
						

							66 Chapter 5   PrintingENWW
 
						

							6 Fax
●Basic fax features and tasks
●
Advanced fax features and tasks
●
Fax logs and reports
●
Sending and receiving faxes by using a computer
●
Other ways to set up your fax
●
Connecting additional devices
NOTE Many of the functions that are described in this chapter also can be performed by
using the HP ToolboxFX. For instructions about using the HP ToolboxFX, see the
HP ToolboxFX online Help.
ENWW 67
 
						

							Basic fax features and tasks
Fax control-panel buttons
The controls for sending faxes are located on the left side of the control panel.
HP LaserJet 3390/3392
HP LaserJet 3050 HP LaserJet 3055
05
06
07
08Shift
This section describes how to fax a document.
Specifying the fax settings
Before you can begin using the all-in-one fax features, you must complete the following tasks:
● Setting the time and date
● Setting the fax header
NOTE
If you are installing the all-in-one software on your computer, you can skip the
remaining instructions in this chapter. The software installer automatically helps you to set up
the fax settings, unless you are using Microsoft  Windows® 95 or Windows NT®. See the
electronic User Guide for instructions.
If you completed the software installation, you are ready to send faxes from your computer. If
you did not complete the fax setup process at  the time you installed the software, you can
complete it at any time by using the Fax Setup Wizard in the all-in-one program group (click
Start, Programs , HP , the name of your all-in-one, and HP Fax Setup Wizard ).
In the United States and many other regions/countries, setting the time, date, and other fax
header information is a legal requirement.
68 Chapter 6   Fax ENWW
 
						

							Setting the time and date
To set the time and date
To set or change the time and date, use the following steps. If you need help entering any
information, see 
Enter text from the control panel.
1. On the control panel, press  Menu.
2. Use the  < or the  > button to select  System setup, and then press 
.
3. Press  Menu to select  Time/Date.
4. Use the  < or the  > button to specify either the 12-hour or the 24-hour clock, and then press 
.
5. Use the alphanumeric buttons to enter the current time.
6. If you specified the 12-hour clock, use the  < or the  > button to move the cursor past the fourth
character. Select  1 for A.M. or  2 for P.M., and then press 
.
-or-
If you specified the 24-hour clock, press 
.
7.
NOTE Make sure that you use two digits to specify the month and day, in that order (for
example, use “05” for May and “01” for the first day of the month of May).
8. Press  Menu.
Setting the fax header
To set the fax header
To set or change the fax header information, complete the following steps. If y\
ou need help entering
any information, see 
Enter text from the control panel.
1. On the control panel, press  Menu.
2. Use the  < or the  > button to select  Fax setup, and then press 
.
3. Use the  < or the  > button to select  Fax Header, and then press 
.
4. Use the alphanumeric buttons to enter your fax number, and then press 
.
5. Use the alphanumeric buttons to enter  your company name, and then press 
.
NOTEThe maximum number of characters allowed in the fax number is 20. The maximum
number of characters allowed in the company name is 40.
ENWW Basic fax features and tasks 69
 
						

							Sending faxes
To send a fax to one recipient
1.Use the alphanumeric buttons on the all-in-one control panel to dial the number.
If the fax number you are calling has  been assigned to a one-touch key, press that key.
-or-
If the fax number you are calling has a speed-dial entry, press  Phone Book, use the
alphanumeric buttons to specify the speed-dial entry, and then press 
.
2. Load the document into the automatic document feeder (ADF) input tray or on the flatbed
scanner.
3. Press  Start Fax . If the pages that you want to  send are in the ADF, then faxing begins
automatically.
4. If the all-in-one ADF sensor detects that no  document is loaded into the ADF input tray,  Send
from glass? 1=Yes 2=No  appears on the control-panel display. To send the fax from the
flatbed scanner, press  1 to select  YES, and then press 
.
After you press 
, Load page:X Press  appears on the control-panel display.
5. If you have already placed the document on the flatbed scanner, press 
 (or place the
document on the flatbed scanner and then press 
).
After scanning the page,  Another page? 1=Yes 2=No  appears on the control-panel display.
6. If you have more pages to scan, press  1 to select  YES, and then repeat step 5 for each page of
the fax job.
-or-
If you are finished, press  2 to select  NO.
When the last page of the fax has exited the  all-in-one, you can start sending another fax, copying, or
scanning.
You can assign a one-touch key or speed-dial entry numbers that you use regularly. See 
To program
or edit speed-dial entries and one-touch keys  and To program group-dial entries . If you have
electronic phone books available, you might be able to use them to select recipients. Electronic
phone books are generated by using third-party software programs.
To send a fax to multiple recipients 
You can send a fax to several fax numbers at once. If you want to send a fax to a group of fax
numbers that you have assigned to a group-dial entry, see the information later in this section about
sending faxes by using group-dial entries. If you want to send a fax to a group of numbers (maximum
of 20) that have  not been assigned a group-dial entry, see the information later in this section about
sending faxes to groups manually (ad hoc faxing).
 In the rare instance that your document does not
 fit into memory, complete one of the following:
Clear saved faxes from the fax memory. For more information, see 
Deleting faxes from memory .
-or-
70 Chapter 6   Fax ENWW
 
						

							Divide the document into smaller sections, and then send the document as multiple fax jobs.
To send a fax by using a group-dial entry
1. Load the document into the automatic document feeder  (ADF) input tray or on the flatbed
scanner.
2. Press the one-touch key for the group.
Press  Phone Book , use the alphanumeric buttons to specify the group-dial entry, and then
press 
.
3. Press  Start Fax . If the pages that you want to send are in the ADF, then faxing begins
automatically.
4. If the all-in-one ADF sensor detects that no document is loaded into the ADF input tray, Send
from glass? 1=Yes 2=No  appears on the control-panel display. To send the fax from the
flatbed scanner, press  1 to select  YES, and then press 
.
After you press 
, Load page:X Press  appears on the control-panel display..
5. If you have already placed the  document on the flatbed scanner, press 
 (or place the
document on the flatbed scanner and then press 
).
After scanning the page,  Another page? 1=Yes 2=No  appear on the control-panel display.
6. If you have more pages to scan, press  1 to select  YES, and then repeat step 5 for each page of
the fax job.
-or-
If you are finished, press  2 to select  NO.
The all-in-one scans the document into memory and sends  the fax to each number specified. If a
number in the group is busy or does not answer,  the all-in-one redials the number based on its redial
setting. If all redial attempts fail, the all-in-one updates  the fax activity log with the error and proceeds
to the next number in the group.
To send a fax to a group manually (ad hoc faxing)
Use the following instructions to send a fax to a group of recipients that has not been assigned a
group-dial entry:
1. Load the document into the automatic document feeder  (ADF) input tray or on the flatbed
scanner.
2. Use the alphanumeric buttons.
If the fax number that you are calling  has been assigned a one-touch key, press that key.
-or-
If the fax number that you are calling has been assigned a speed-dial entry, press  Phone Book,
use the alphanumeric buttons to specify the speed-dial entry, and then press 
.
3. Press 
.
4. To continue dialing numbers, repeat steps 2 and 3.
ENWW Basic fax features and tasks 71
 
						

							-or-
If you are finished dialing numbers, go to the next step.
5. Press  Start Fax . If the pages that you want to  send are in the ADF, then faxing begins
automatically.
6. If the all-in-one ADF sensor detects that no  document is loaded into the ADF input tray,  Send
from glass? 1=Yes 2=No  appears on the control-panel display. To send the fax from the
flatbed scanner, press  1 to select  YES, and then press 
.
After you press 
, Load page: X Press  appears on the control-panel display..
7. If you have already placed the document on the flatbed scanner, press 
 (or place the
document on the flatbed scanner and then press 
).
After scanning the page,  Another page? 1=Yes 2=No  appears on the control-panel display.
8. If you have more pages to scan, press  1 to select  YES, and then repeat step 7 for each page of
the fax job.
-or-
If you are finished, press  2 to select  NO.
The all-in-one sends the fax to each fax number. If  a number in the group is busy or does not
answer, the all-in-one redials that number based on its  redial setting. If all redial attempts fail, the all-
in-one updates the fax activity log by adding the error, and then it proceeds to the next number in the
group.
NOTE The fax activity log feature is not supported in the software for Windows 98 or
Windows Me, but you can print the fax activity  log by using the control panel. For instructions,
see 
Printing the fax activity log .
72 Chapter 6   Fax ENWW