HP LaserJet 3052 User Manual

							Clearing stapler jams
To reduce the risk of staple jams, make sure that you staple 20 or fewer pages of media (80 g/m2 or
20 lb) at a time.
To clear a staple jam from the convenience stapler
1. Turn off the HP LaserJet 3392 all-in-one,  and then open the stapler door.
NOTEOpening the stapler door disables the stapler.
2.Remove the staple cassette from the all-in-one.
3.Clear any loose staples from the stapler and from the staple cassette.
ENWW Clearing stapler jams 193
 
						

							4.Replace the staple cassette.
5.Close the stapler door and then  turn on the HP LaserJet 3390/3392 all-in-one.
6.Insert media to test the convenience stapler. Repeat steps 1 through 6 if necessary.
194 Chapter 10   Convenience stapler (HP LaserJet 3392 all-in-one only) ENWW
 
						

							11 How do I?
●Print: How do I?
●
Fax: How do I?
●
Copy: How do I?
●
Scan: How do I?
●
Network: How do I?
●
Other: How do I?
ENWW 195
 
						

							Print: How do I?
Use this section to answer printing questions.
Change the all-in-one print settings, such as volume or print
quality, in HP ToolboxFX
To change the default print settings in HP ToolboxFX, complete the following steps.
NOTEThe changes that you make to the print settings in HP ToolboxFX apply to all future
print jobs.
1. Open HP ToolboxFX and click  Device Settings.
2. Click the  System Settings  tab.
3. On the  System Settings  tab, you can modify settings that appear on the following pages. Each
page offers Help for more information.
● Device Information
● Paper Handling
● Print Quality
● Print Density
● Print Modes
● System Setup
● Date/Time
● Service
● Device Polling
● Save/Restore
4. Click  Apply  to save the changes that you make on these pages.
NOTE If you have similar settings in the printer driver, those settings take priority over the
settings that are established in HP ToolboxFX.
196 Chapter 11   How do I? ENWW
 
						

							Print on both sides (Windows)
Automatic two-sided printing (duplexing) is available using the automatic duplexer on the
HP LaserJet 3390/3392 all-in-one. Manual duplexing is available on the HP LaserJet
3050/3052/3055/3390/3392 all-in-one. To duplex manually, print on both sides of a page by feeding
the page through the all-in-one twice.
NOTE In the printer driver,  Print on Both Sides (manually)  is available only when duplex
printing is not available or when duplex printing is not supported for the type of print\
 media
being used.
To print on both sides  automatically (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to accommodate the print job. If you are loading
special paper such as letterhead, load it  in one of the following ways:
● For tray 1, load the letterhead paper with the front side up, bottom-edge first.
● For all other trays, load the letterhead paper with
 front side down, and the top edge at the
back of the tray.
CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond). This could lead
to a jam in the all-in-one.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. For Windows, on the  Finishing tab, click  Print on Both Sides .
4. Click  OK. The product is now ready to print on both sides of the paper.
To print on both sides manually (HP LaserJet 3050/3052/3055 all-in-one)
NOTE The printer driver also contains instructions and graphics for manually duplexing.
1.In the software program, open the all-in-one properties (printer driver).
2. On the  Finishing  tab, select  Print on Both Sides .
NOTEIf the Print on Both Sides  option is dimmed or unavailable, open the all-in-one
properties (printer driver). On the  Device Settings tab or the Configure tab, select
Allow Manual Duplexing , and then click OK. Repeat steps 1 and 2.
3. Print the document.
ENWW Print: How do I? 197
 
						

							4.After one side has been printed, remove the remaining media from the input tray, and set it
aside until after you finish your manual duplexing job.
HP LaserJet 3050 HP LaserJet 3052/3055
5.Gather the printed pages, keep the printed  side facing down, and straighten the stack.
HP LaserJet 3050 HP LaserJet 3052/3055
6.Place the stack of media in the input tray again.  The printed side should be facing down with the
top edge feeding into the all-in-one first.
1
HP LaserJet 3050 HP LaserJet 3052/3055
7.On the computer screen, click  OK and wait for the second side to print.
198 Chapter 11   How do I? ENWW
 
						

							To print on both sides manually (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to accommodate the print job. If you are loading
special paper such as letterhead, load it  in one of the following ways:
● For tray 1, load the letterhead paper with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front side down, and the top edge at the back
of the tray.
CAUTION
Do not load paper that is heavier than 105 g/m2 (28 lb bond). Jamming could
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. On the  Finishing  tab, select  Print on Both Sides (manually) .
4. Click  OK.
5. Send the print job to the product.
6. Go to the all-in-one. Remove any blank paper that is in tray 1.  Insert the printed stack into the
tray that is specified on the control panel.  Load the paper with the printed side up, and the
bottom-edge feeding into the all-in-one first. Follow the instructions in the pop-up window that
appears before feeding the output stack back for  printing the second half of the job.
7. A prompt might appear on the control-panel display that instructs you to press a button to
continue.
ENWW Print: How do I? 199
 
						

							Print on both sides (Macintosh)
Automatic two-sided printing (duplexing) is available by using the automatic duplexer on the
HP LaserJet 3390/3392 all-in-one. Manual duplexing is available on the HP LaserJet
3050/3052/3055/3390/3392 all-in-one. To duplex manually, print on both sides of a page by feeding
the page through the all-in-one twice.
To print on both sides automatically (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to  accommodate the print job. If you are loading
special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper with 
the front side up and the bottom-edge feeding
into the all-in-one first.
● For all other trays, load the letterhead paper with the front side down and the top edge at
the back of the tray.
CAUTION
Do not load paper that is heavier than 105 g/m2 (28-lb bond). Jamming might
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. Open the  Layout pop-up menu.
4. Next to  Two Sided Printing , select either Long-Edge Binding  or Short-Edge Binding .
5. Click  Print.
200 Chapter 11   How do I? ENWW
 
						

							To print on both sides manually (HP LaserJet 3050/3052/3055 all-in-one)
1.In the software program, open the all-in-one properties (printer driver).
2. On the  Finishing  tab, select  Manually print on 2nd side .
3. Print the document.
4. After one side has been printed, remove the remaining media from the input tray, and set it
aside until after you finish your manual duplexing job.
HP LaserJet 3050 HP LaserJet 3052/3055
5.Gather the printed pages, keep the printed side facing down, and straighten the stack.
HP LaserJet 3050 HP LaserJet 3052/3055
6.Place the stack of media in the input tray again. The printed side should be facing down with the
top edge feeding into the all-in-one first.
1
HP LaserJet 3050 HP LaserJet 3052/3055
7.On the computer screen, click  OK and wait for the second side to print.
ENWW Print: How do I? 201
 
						

							To print on both sides manually (HP LaserJet 3390/3392 all-in-one) (Macintosh)
1.Insert enough paper into one of the trays to  accommodate the print job. If you are loading
special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper 
with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front
 side down, and the top edge at the back
of the tray.
CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond). Jamming could
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. On the  Finishing  tab, select  Print on Both Sides (manually) .
4. Click  OK.
5. Send the print job to the product.
6. Go to the all-in-one. Remove any blank paper that is in tray 1.  Insert the printed stack into the
tray that is specified on the control panel.  Load the paper with the printed side up, and the
bottom-edge feeding into the all-in-one first. Follow the instructions in the pop-up window that
appears before feeding the output stack back for  printing the second half of the job.
7. A prompt might appear on the control-panel display that instructs you to press a button to
continue.
Use the single-sheet priority input slot (tray 1)
The single-sheet priority input slot holds one  sheet of media up to 163 g/m2 (43 lb) in weight or one
envelope, transparency, or card. Load media with the top forward and the side to be printed facing
up. To prevent jams and skewing, always adjust the side media guides before feeding the media.
NOTE When feeding media into the single-sheet priority input slot, the all-in-one pulls the
media partially into the all-in-one. You must wait for the all-in-one to stop before feeding
another sheet of media. You can only feed one sheet of media at a time.
202 Chapter 11   How do I? ENWW